User manual WHIRLPOOL WTW8900BW WARRANTY INFORMATION

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WTW8900BW. We hope that this WHIRLPOOL WTW8900BW user guide will be useful to you.


WHIRLPOOL WTW8900BW WARRANTY INFORMATION: Download the complete user guide (295 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WTW8900BW ENERGY GUIDE (373 ko)
   WHIRLPOOL WTW8900BW DIMENSION GUIDE (505 ko)
   WHIRLPOOL WTW8900BW USE & CARE GUIDE (5055 ko)
   WHIRLPOOL WTW8900BW INSTALLATION GUIDE (4701 ko)

Manual abstract: user guide WHIRLPOOL WTW8900BWWARRANTY INFORMATION

Detailed instructions for use are in the User's Guide.

[. . . ] Top of standpipe must be at least 39" (990 mm) high; install no higher than 96" (2. 2 (155 cm2) 5" (126 mm) 1" (25 mm) 1" (25 mm) 3" (76 mm) Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. [. . . ] If a closet door or louvered door is installed, top and bottom air openings in door are required. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. To order, please see toll-free phone numbers in your Use and Care Guide. Top of laundry tub must be at least 39" (990 mm) above floor; install no higher than 96" (2. 5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. 3 ELECTRICAL REQUIREMENTS INSTALLATION INSTRUCTIONS Before you start: remove shipping materials It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer. It is recommended that a separate circuit breaker serving only this appliance be provided. N This washer is equipped with a power supply cord having a 3 prong grounding plug. N To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician. If you are only connecting to a cold water faucet, you must use a Y-adapter (not provided). IMPORTANT: To reduce risk of hose failure, replace the hoses every 5 years. n Periodically inspect and replace hoses if bulges , kinks , cuts , Attach hose to hot water faucet. IMPORTANT: Do not overtighten or use tape or sealants on valve when attaching to faucets or washer. 5" (113 (114 mm) Jam nut Models with metal feet or Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with cable tie. Check levelness of washer Place level here Place level here If washer is not level: On models with metal feet, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts clockwise on feet until they are about 1/2" (13 mm) from the washer cabinet. Then turn the leveling foot clockwise to lower the washer or counterclockwise to raise the washer. On models with plastic feet, use adjustable pliers to turn the plastic leveling foot counterclockwise to lower the washer or clockwise to raise the washer. Rock washer back and forth to make sure all four feet make solid contact with floor. If washer is level, skip to step 15, (on models with metal feet) or step 16 (on models with plastic feet). [. . . ] HELPFUL TIP: You may want to prop up front of washer about 4" (102 mm) with a wood block or similar object that will support weight of washer. Tighten leveling feet Jam nut Not Level LEVEL Not Level On models with metal feet, when washer is level, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts counterclockwise on leveling feet tightly against washer cabinet. Q Check that shipping materials were completely removed from washer. Q To test and clean your washer, measure 1/2 of normal recommended amount of powdered or liquid detergent and pour it into washer basket or detergent dispenser (on some models). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WTW8900BW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WTW8900BW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.