User manual WHIRLPOOL WGD9600T DIMENSION GUIDE

[. . . ] ® Gas Dryer PRODUCT MODEL NUMBERS WGD9200S WGD9300V WGD9400S WGD9400V WGD9500T WGD9600T REQUIREMENTS Electrical: A 4-wire, single-phase, 120/240-volt, 60-Hz, AC-only electrical supply on a separate 30-amp circuit, fused on both sides of the line is required. Exhaust outlet hood must be at least 12" (30. 5 cm) from the ground or any object that may be in the path of the exhaust. [. . . ] NOTE: Pipe joint compounds that resist the action of LP gas must be used. Do not use TEFLON® tape. * Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to avoid kinking. This dryer must be connected to the gas supply line with a listed flexible gas connector that complies with the standard for connectors for gas appliances, ANSI Z21. 24 or CSA 6. 10. An individual manual shutoff valve must be installed within six (6) feet (1. 8m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223. 1. Dupont De Nemours and Company Dryer gas pipe: The gas pipe that comes out through the rear of your dryer has a 3/8" male thread. *6¼" (15. 9 cm) B A A. 3/8" NPT dryer pipe 1½" (3. 8 cm) NOTE: If the dryer is mounted on a pedestal, the gas pipe height must be an additional 10" (25. 4 cm) or 15. 5" (39. 4 cm) from the floor, depending on the pedestal model. For a garage installation, the gas pipe height must be an additional 18" (46 cm) from the floor. PRODUCT DIMENSIONS D Steam (Electric or Gas) A A B C D B C 38" (9652 mm) 32 /16" (686 mm) 9 Non-Steam (Electric or Gas) 38" (9652 mm) 31 1/2" (800 mm) 27" (686 mm) 51 1/2" (1308 mm) 27" (686 mm) 52 9/16" (1335 mm) * Most installations require a minimum 5" (127 mm) clearance behind the dryer for the exhaust vent with elbow. Page 1 of 3 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. For complete details, see Installation Instructions packed with product. W10224610 11-09-08 ® Gas Dryer PRODUCT MODEL NUMBERS WGD9200S WGD9300V WGD9400S WGD9400V WGD9500T WGD9600T RECESSED AREA AND CLOSET INSTALLATION For closet installation, with a door, the minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent air ventilation openings in the top and bottom are acceptable. Closet installation - Dryer only Recessed or closet installation - Dryer on pedestal (460 mm) (460 mm) A* B C** Closet door with vents A B C D* E F** Side view Steam (Electric or Gas) A B C D* E F** 1" (25 mm) 27" (686 mm) 1" (25 mm) 1" (25 mm) 32 9/16" (686 mm) 5" (127 mm) Non-Steam (Electric or Gas) 1" (25 mm) 27" (686 mm) 1" (25 mm) 1" (25 mm) 31 1/2" (800 mm) 5" (127 mm) Steam (Electric or Gas) A* B C** 1" (25 mm) 32 9/16" (686 mm) 5" (127 mm) Non-Steam (Electric or Gas) 1" (25 mm) 31 1/2" (800 mm) 5" (127 mm) *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed. *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed NOTE: Some models are not recommended for recessed or closet installation. RECOMMENDED INSTALLATION SPACING FOR CABINET INSTALLATION NOTE: Some models are not recommended for cabinet installation. For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required. [. . . ] Determine the number of elbows you will need. Page 3 of 3 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. For complete details, see Installation Instructions packed with product. [. . . ]