User manual WHIRLPOOL WGD5810BW DIMENSION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WGD5810BW. We hope that this WHIRLPOOL WGD5810BW user guide will be useful to you.


WHIRLPOOL WGD5810BW DIMENSION GUIDE: Download the complete user guide (620 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WGD5810BW (5080 ko)
   WHIRLPOOL WGD5810BW INSTALLATION GUIDE (9770 ko)
   WHIRLPOOL WGD5810BW INSTALLATION GUIDE (9770 ko)
   WHIRLPOOL WGD5810BW (5080 ko)
   WHIRLPOOL WGD5810BW INSTALLATION GUIDE (9770 ko)

Manual abstract: user guide WHIRLPOOL WGD5810BWDIMENSION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Optional Equipment: (Not supplied with dryer) Level Pliers Refer to your “Use and Care Guide” for information about accessories available for your dryer. Location Requirements Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Caulking gun and compound (for installing new exhaust vent) Utility knife Putty knife ■■ 4 You will need: A location allowing for proper exhaust installation. –■ If you are using power supply cord, a grounded electrical outlet located within 2 ft. € ■■ A sturdy floor to support dryer and a total weight (dryer and load) of 200 lbs. [. . . ] For mobile home use Gas dryers must be securely fastened to the floor. mobile home installations require a Mobile Home Installation Hold-down Kit. For ordering information, please reference the “Use and Care Guide. –■ Must include 1/8" NPT minimum plugged tapping accessible for test gauge connection, immediately upstream of the gas connection to the dryer (see illustration). : An individual manual shut-off valve must be installed within six (6) feet (1. 8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223. In Canada: An individual manual shut-off valve must be installed in accordance with the B149. It is recommended that an individual manual shut-off valve be installed within six (6) feet (1. The shut-off valve location should be easy to reach for opening and closing. –■ ■■ E C A ■■ If your dryer has been converted to use LP gas, 3/8" LP compatible copper tubing can be used. NOTE: Pipe joint compounds that resist the action of LP gas must be used. NOTE: If using an existing vent system, clean lint from entire length of the system and make sure exhaust hood is not plugged with lint. –■ ■■ 9 Exhaust hoods: ■■ Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow). Plan Vent System Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Optional side exhaust outlet Elbows: ■■ 45° elbows provide better airflow than 90° elbows. Good Better Optional exhaust installations: 27" Wide Models can be converted to exhaust out the right side, left side, or through the bottom (4-way vent kit). Exhaust vent must not be connected or secured with screws or other fastening devices that extend into interior of duct and catch lint. Bottom exhaust installation (27" wide models only) 10 Alternate installations for close clearances Venting systems come in many varieties. Special provisions for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Over-The-Top installation (also available with one offset elbow) Determine vent path: ■■ ■■ ■■ ■■ ■■ Periscope installation Select route that will provide straightest and most direct path outdoors. NOTE: The following kits for close clearance alternate installations are available for purchase. Determine vent length and elbows needed for best drying performance: ■■ Use following “Vent System Chart” to determine type of vent material and hood combinations acceptable to use. [. . . ] Reattach outer door panel to inner door panel so handle is on the side where hinges were just removed. Insert screws in hinge holes on dryer cabinet Door strike Door strike plug Remove door strike and door strike plug from dryer cabinet. Insert the door strike into door strike plug hole and secure with screw. Insert door strike plug into original door strike hole and secure with screw. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WGD5810BW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WGD5810BW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.