User manual WHIRLPOOL AWM 020 INSTRUCTION FOR USE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL AWM 020. We hope that this WHIRLPOOL AWM 020 user guide will be useful to you.


WHIRLPOOL AWM 020 INSTRUCTION FOR USE: Download the complete user guide (510 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL AWM 020 KURZANLEITUNG (138 ko)
   WHIRLPOOL AWM 020 MODE D'EMPLOI (461 ko)
   WHIRLPOOL AWM 020 GEBRUIKSAANWIJZING (425 ko)
   WHIRLPOOL AWM 020 BEDIENUNGSANLEITUNG (429 ko)
   WHIRLPOOL AWM 020 PRODUCT-INFORMATIEBLAD (139 ko)
   WHIRLPOOL AWM 020 PROGRAM CHART (137 ko)

Manual abstract: user guide WHIRLPOOL AWM 020INSTRUCTION FOR USE

Detailed instructions for use are in the User's Guide.

[. . . ] GB QUICK REFERENCE GUIDE THE FIRST TIME THE APPLIANCE IS USED: • FOLLOW THE "INSTALLATION INSTRUCTIONS" • REMOVE THE TRANSIT BOLTS BEFORE USING THE APPLIANCE. Pour a small amount of detergent (about 100 ml) into the detergent dispenser 4. The Power On led lights up to indicate that the machine is switched on. This initial cycle serves to eliminate any water remaining after your appliance was tested at the factory. [. . . ] Hold down the "Start" button for 5 seconds, or until the programme control audibly restarts and the remaining time indicator displays "00". Wait until the programme sequence indicator has returned to its initial (leftmost) position. Hold down the "Start"-button for about 1 second. TO INTERRUPT/PAUSE A PROGRAMME To interrupt a programme for a certain time and resume it later: 1. Hold down the "Start" button for about 1 second. TO STOP A PROGRAMME BEFORE THE END AND DRAIN To stop a programme before it has finished and drain the water: 1. The programme sequence indicator returns to its initial (leftmost) position. The water drains. REMOVING THE FILTER / DRAINING RESIDUAL WATER WHEN SHOULD I REMOVE THE FILTER? • • • Check the filter two or three times a year and clean it if necessary. Check the filter if the appliance is not draining properly or if it fails to perform spin cycles. Remove the filter if the pump is blocked by an object (buttons, coins, safety pins, etc. ). IMPORTANT: make sure the water has had time to cool before draining the appliance. REMOVING THE FILTER 1. Switch off the appliance (set the programme selector to "0". ) 2. Remove the coloured insert from the detergent dispenser and use it to open the filter cover. Turn the filter slowly anti-clockwise until the grip is vertical; do not extract filter as yet. Insert the filter and screw it fully down in a clockwise direction (until the grip is horizontal). Pour 0. 5 l of water into the detergent dispenser to reactivate the "Eco System". Select the programme and hold down the "Start" button about 1 second. WHEN SHOULD I DRAIN RESIDUAL WATER? • • Before transporting (moving) the machine. If the appliance is installed in a room subject to subzero temperatures. It is best in this case to drain the machine after every wash. DRAINING RESIDUAL WATER The residual water drain hose is accommodated in the appliance plinth. Unscrew the plastic screw using the thin rounded projection on the coloured insert from the detergent drawer. Allow all the water to flow into a flat bowl, then refit the plug and stow the drain tube back in its compartment. Before using the machine again, pour about 1 litre of water into the detergent dispenser to reactivate the "Eco System". 31 CARE AND MAINTENANCE APPLIANCE EXTERIOR AND CONTROL PANEL • • Clean using normal household cleaner (do not use abrasive products). Disengage the detergent dispenser by pressing the release lever in the prewash compartment, and extract it. Remove the inserts (the siphon from the softener compartment and the insert for liquid detergents). [. . . ] If the flexible hose is damaged, unplug the appliance from the mains immediately. If the hose is too short, replace it with a 3 m Water Stop hose (available from After Sales Service or from your dealer). This operation must be carried out exclusively by a licensed electrician. Connect the drain hose to the siphon or hook it over the edge of a sink by means of the "U" bend (see figure). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL AWM 020




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL AWM 020 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.