User manual WHIRLPOOL AKT7000MR

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL AKT7000MR. We hope that this WHIRLPOOL AKT7000MR user guide will be useful to you.


WHIRLPOOL AKT7000MR : Download the complete user guide (1408 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL AKT7000MR (1459 ko)

Manual abstract: user guide WHIRLPOOL AKT7000MR

Detailed instructions for use are in the User's Guide.

[. . . ] In the event of problems, contact the dealer or your nearest After-sales Service. WARNING - If the information in this manual is not followed exactly, a fire or explosion may result causing property damage or injury. TECHNICAL INFORMATION FOR THE INSTALLER • • • Use protective gloves for handling, preparing and installing the product. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is equipped with a cooling system. [. . . ] IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. • After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position to minimum position to check flame stability. C C A B C 5019 300 02773 Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY ELECTRICAL CONNECTION WARNING WARNING This operation must be performed by a qualified technician. • • • The electrical connections must comply with local regulations. L Earth (yellow/green) N IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap if found to be faulty. IMPORTANT: when gas cylinder is adopted, the gas cylinder or gas container must be properly settled (vertical orientation). REPLACING THE INJECTORS (see the injector table in the Instruction) • • • Remove grids (A). Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to be replaced. • If you have a multiple crown burner use side spanner to replace the injector (E). Before installing the hob, remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration. IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. NOTE: the power supply cable must be long enough to permit its upward extraction. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures). Top 20 mm 20 ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows: • tighten screw to reduce the flame height (-); • loosen screw to increase the flame height (+). The adjustment must be performed with the tap in minimum gas setting position (small flame) . • 60 Top 40 mm 40 Top 30 mm 30 Top 60 mm At this stage, light up the burners and turn the knobs from max position to minimum position to check flame stability. Upon completion of adjustment, reseal using sealing wax or an equivalent material. NO REFERENCE TO LOCAL REGULATIONS Ensure that the installation and gas connections are performed by a qualified technician, following the manufacturer's instructions and in compliance with current local safety regulations. AFTER-SALES SERVICE ADJUSTMENT TO DIFFERENT TYPES OF GAS WARNING This operation must be performed by a qualified technician. Before calling the After-Sales Service, make sure you can give the following information: - type of fault or problem; - exact model (written on the label affixed to the instruction/warranty); - service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction/warranty; - your complete address and phone number. If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. • The gas injector must be changed by After Sales Service or a qualified technician. [. . . ] • To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting. • After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation. This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally (because of sudden draught, an interruption in the gas delivery, boiling over of liquids, etc. ). If, after that time has elapsed, the burner does not remain lit, wait at least one minute before trying to light it again. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL AKT7000MR




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL AKT7000MR will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.