User manual WHIRLPOOL ACM794NE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL ACM794NE. We hope that this WHIRLPOOL ACM794NE user guide will be useful to you.


WHIRLPOOL ACM794NE : Download the complete user guide (3555 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL ACM794NE (1575 ko)
   WHIRLPOOL ACM794NE (1510 ko)
   WHIRLPOOL ACM794NE (1562 ko)
   WHIRLPOOL ACM794NE (1559 ko)
   WHIRLPOOL ACM794NE (1560 ko)
   WHIRLPOOL ACM794NE (1509 ko)

Manual abstract: user guide WHIRLPOOL ACM794NE

Detailed instructions for use are in the User's Guide.

[. . . ] Do not repair or replace any part of the appliance unless specifically stated in the user manual. - The power cable must be long enough for connecting the appliance, fitted in the cabinet, to the power supply. - For installation to comply with the current safety regulations, an omnipolar switch with minimum contact gap of 3mm is required. - The electrical parts must not be accessible to the user after installation. [. . . ] For delicate cooking (for example, melting chocolate or butter) use the smaller diameter single zones. INSTALLATION After unpacking the product, check for any damage during transport. For built-in dimensions and installation instruction, see the pictures in page 2. PREPARING THE CABINET FOR FITTING WARNING • • • • • • Install a separator panel under the hob. The lower part of the product must not be accessible after installation. Do not fit the separator panel if an undertop oven is installed. min. 20 mm 6-7 cm The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure. In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an undertop oven is installed, make sure the oven is equipped with a cooling system. Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them. In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112. To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance. EN6 ELECTRICAL CONNECTION Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. WARNING - - Connection to the terminal block For the electrical connection of the power cord is present in the supply. Remove the terminal cover (A) by unscrewing the screw and insert the cover into the hinge (B) of the terminal. Plug the power cord into the clamp and connect the wires to the terminal block as shown in the wiring diagram located near the terminal. The cooking zone switches off and, if still hot, the letter “H” appears on the zone display. Control panel lock This function locks the controls to prevent accidental activation of the hob. To activate the control panel lock, switch the hob on and press the Lock function button for three seconds; an acoustic signal and a luminous indicator near the padlock symbol signal activation. The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can accidentally activate or deactivate the control panel lock. EN8 Timer The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39 minutes) for all the cooking zones. Select the cooking zone to be used with the timer, press the timer (see figure) and a beep signals the function. The Timer value can be decreased and increased by keeping the slider function “+” and “-” buttons pressed. When the set time has elapsed, an acoustic signal sounds and the cooking zone switches off automatically. [. . . ] Increase / decrease the cooking zones activated, the background noise of the fan may increase or decrease. These conditions are normal and essential for the proper functioning of the induction system, they are not indication of failure or damage. EN10 AFTER-SALES SERVICE Before contacting the After-sales Service: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. Switch the appliance off and then on again it to see if the problem has been eliminated. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL ACM794NE




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL ACM794NE will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.