User manual WHIRLPOOL 9762996

[. . . ] When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225. 1/NFPA 501A or local codes. Mobile home installations require: s When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above. s Parts supplied Check that all parts are included. A B Four-wire power supply cord or cable must be used in a mobile home installation. #10 x 1¹/" screws (2) s Product Dimensions Anti-tip brackets must be securely mounted to subfloor. [. . . ] Cord should be Type SRD or SRDT with a UL listed strain relief and be at least 4 ft (1. 22 m) long. The minimum conductor sized for the copper 4-wire power cord are: 40-amp circuit 2 No. -8 conductors 1 No. -10 white neutral 1 No. -8 green grounding If connecting to a 3-wire system: Local codes may permit the use of a UL listed, 3-wire, 250-volt, 40- or 50-amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 10-50P plug on the supply end. Connectors on the appliance end must be provided at the point the power supply cord enters the appliance. This uses a 3-wire receptacle of NEMA Type 10-50R. 3-wire receptacle (10-50R) 4-wire receptacle (14-50R) INSTALLATION INSTRUCTIONS Unpack Range WARNING Excessive Weight Hazard Use two or more people to move and install range. Use a ³/" drive ratchet to lower the rear leveling legs one-half turn. Use a wrench or pliers to lower front leveling legs one-half turn. A D C B A. Front leveling leg A On Ranges Equipped with Warming Drawers: Use a wrench or pliers to lower the front and rear leveling legs one-half turn. If cabinet opening is wider than that specified in the "Location Requirements" section, adjust template so range will be centered in cabinet opening. To mount anti-tip bracket to wood floor, drill two ¹/" (3. 2 mm) holes at the positions marked on the bracket template. Only Power Supply Cord Direct Wire WARNING WARNING Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Remove the terminal block cover screws located on the back of the range. Style 1: Power supply cord strain relief s s Remove the knockout for the power supply cord. UL listed strain relief s Tighten strain relief screw against the power supply cord. C A. Hex-head screws 6 Style 2: Direct wire strain relief s s Remove the knockout as needed for the flexible conduit connection. Assemble a UL listed conduit connector in the opening. 4-wire connection: Power supply cord Use this method for: s New branch-circuit installations (1996 NEC) s s s Mobile homes Recreational vehicles In an area where local codes prohibit grounding through the neutral A 1. Bend the ground-link away from the range so that it does not contact the range. B A. Strain relief s Tighten strain relief screw against the flexible conduit. C B A A. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) Electrical Connection Options If your home has: 4-wire receptacle (NEMA type 14-50R) And you will be connecting to: A UL listed, 250-volt minimum, 40-amp, range power supply cord Go to Section: 2. Connect the green ground wire from the power supply cord to the range using the ground-link screw and cup washer. The ground wire must be attached first and must not contact any other terminal. [. . . ] For more information, read the "Range Care" section of the Use and Care Guide. See the Use and Care Guide for specific instruction on range operation. If range does not operate, check the following: s Household fuse is intact and tight; or circuit breaker has not tripped. s s s 1. Check that anti-tip bracket is installed: s Look for the anti-tip bracket securely attached to floor. s Slide range back so rear range foot is under anti-tip bracket. 4. [. . . ]