User manual WHIRLPOOL 8204864

[. . . ] 8204864/3828W5U0311 Before you start. . . Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING. " These words mean: Tools recommended for installation: Assemble the required tools and parts before starting installation. [. . . ] Location of template: Select the easiest position to work from, either on the inside bottom of the cabinet or the underside of the cabinet to locate the template. When putting the template in place, make sure the front of the cabinet is directly above the front of the microwave oven cabinet, not the microwave oven door. Go to "Template instructions" on next page. 1. A 2. IMPORTANT: Observe all governing codes and ordinances. It is the customer's responsibility: To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 -- latest edition*, and all local codes and ordinances. You must have: 120-volt, 60Hz, AC-only, 15 or 20 amp, fused (or circuit breaker) grounded electrical supply. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Insert each screw into a threaded hole in the top of the oven. Turn each screw three or four times to start the screw into the threaded hole 6b. If the cabinet does not have a front frame extending below the cabinet bottom: Slide one spacer over each of the four mounting screws or, for a smaller gap, use 1/4" I. D. flat washers available from hardware store. supplied spacers or 1/4" I. D. flat washers 3. Once the template is in place and taped down, use a center punch, or a nail, to mark the position of the 4 holes, as shown on the template. 6. Drill 4 holes through the cabinet at the marked locations, using a 1/2" (12. 7 mm) drill bit. If the microwave oven is used later as a countertop model, these plugs will need to be replaced. If the cabinet has a front frame extending below cabinet bottom go to Step 6a. If the cabinet does not have a front frame extending below the cabinet bottom go to Step 6b. Insert each screw into a threaded hole in the top of the oven. Turn each screw three or four times to start the screw into the threaded hole. 7. Recommended ground method For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3 prong ground plug. To minimize possible shock hazard, the cord must be plugged into a mating 3 prong ground-type wall outlet, grounded in accordance with the National Electrical Code, ANSI/NFPA 70 -- latest edition*, and all local codes and ordinances. 3 prong ground plug power supply cord 3 prong ground-type wall receptacle ground prong Copies of the standards listed may be obtained from: * National Fire Protection Association One Batterymarch Park Quincy, Massachusetts 02269 Lift the microwave oven so the mounting screws enter into the four holes in the bottom of the cabinet. Slowly tighten the four screws evenly until the oven is completely secure and level. If the cabinet has a front frame extending below cabinet: Measure the distance from the bottom of the cabinet to the bottom of the front frame, to determine which of the mounting screws provided, (short or long) and how many of the spacers provided, will need to be used to install the oven properly. 8. 9. To get the most efficient use from your under-the-cabinet microwave oven, read your Use and Care guide. 3 Template instructions Drilling from inside the cabinet If you cannot drill from inside the cabinet, see "Drilling from under the cabinet" section. [. . . ] Position Template B toward the rear of the cabinet so that the hole centerline is aligned with the hole centerline of the Template A piece positioned in Step 3 above. Position the other piece of Template A under the adjacent cabinet opening so that the hole centerline aligns with the hole centerline on Template B. If you have followed the instructions properly, the distance between the right and left hole centerlines will be 12-7/8" (32. 7 cm). front frame of cabinet Template B 4. Position Template B in front of the cabinet so that the hole centerline is aligned with the hole centerline of the Template A piece positioned in Step 3 above. [. . . ]