User manual WHIRLPOOL 4211597

[. . . ] Hold disposer with other hand Turn jam-breaker wrench or screwdriver counterclockwrse until lug lines up with one of the sink-mounting assembly screws. Check that all parts were included. Drawing shows just one model type. Mounting assembly sink flange F!!v 2 rubber I ";y I screw I Caution: Potential gasket screw(s) metal flange Property Damage. Hold disposer with one hand while turning to prevent it from falling when the mountrng ring is disconnected. If old disposer mounting is different from your new one, remove the nuts on the mounting ring usrng pliers or an adjustable wrench. D. Turn disposer upside down and remove the electrical plate. snap ring 2 Electrical requirements E. A U. L. -listed conduit Electrical ground is required on this appliance. must be provided box. connector at the junction E* Use a screwdriver to remove the grounding wire Remove wire nuts from power wires. [. . . ] Hole rim must be as clean as possible for a yood, watertight seal. 4 A. Use wrench "P"-trap. To install our sink's firs Y disposer : to loosen nut at top of PANEL A 6. Loosen the large-diameter nut at the base of the strainer by placing the trp of a screwdriver on the ridge of the nut and gently tapping the screwdnver with a hammer. 8 Attach the upper mounting mm assembhr, A. Working from under sink, slip the ccond rubber gasket, then the metal back-up ring (flat side up>, up and over sink flange IA gasket D. Holding the rubber gasket and metal backup ring in place, attach the mounting ring to the sleeve with the three mounting ring screws Do Not tighten screws at this time. C. Push the strarner assembly up through the sink hole and remove mounting ring further up sink sleeve. Slide snap ring onto sink sleeve until it pops Into place in the sleeve yroove. If installing in a new home, go to Step 6. Remove drain trap Using an auger, clean out the horizontal drain pipe that runs from the trap to the main waste pipe. Watch these t&b spots when routin the auger. 5 Clean sinkS drain line. D. Tighten mounting screws until entire mounting assembly is seated evenly and tightly against sink. 1D. t-i I A. Separate the mounting assembly. A Holding the mounting assembly with one hand, use the other hand to insert jambreaker wrench into one of the lugs of the lower mounting ring. Turn assemblycounterclockwise and remove. Remove electrical plate from the bottom of the new disposer Pull out the black and white electrical wires Locate the yreen grounding screw under plate. Insert strain relief Into hole Insert power supply cable through strain relief. disposer wires using electrical wire nuts or by soldering wires together. If connection is made to aluminum house wiring, use only special connectors which are approved for joining copper to aluminum wires in accordance with the national electrical code and local codes and ordinances. 9 Make electrical connections l 1 _ C. Loosen screws on mounting assembly until they are level with mounting ring surface. C. Take assembly apart and set aside I w Electrical ground is required on this appliance. Failure to follow these instructions could result in death or electric shock. 7 A. If sink Apply rubber asket or putty so sink flange. Electrical ground is required on this appliance. DO NOT reconnect electrical current to main service panel until proper ground is installed. A. If the cable leading to the disposer has three wires, attach the green grounding wire to the green Qrounding screw. Go to Step 10-D The rubber sink flange gasket should always be used where possible. If the cable does NOT have a grounding wire, attach a length of copper wire (no smaller than the other cable wire) to the yreen yrounding screw metal cold water pipet IA. - U C. Attach the other end of the grounding wire opening does not permit the use of a rubber seal, plumber's putty may be used. to a yrounded DO NOT ground to a gas supply line or hot water supply line. Use grounding clamp to secure wire to pipe. If non-metal or plastic pipe IS used In water connectrons or water supply you must have a qualifted electrician install a proper yround. *Grounded cold water pipe must have metal contlnulty to electrlcal ground and not be Interrupted by plastic, rubber or other electrIcallnsulatlny connectors such as hoses, flttlngs, washers, or gaskets (Including water meter or pump) C. Push down gently, but firmly to make sure flange sits evenly over yasket or In putty PANEL B D. Check to see if you have a water meter in your home. [. . . ] Secure flange and waste line pipe to disposer wrth scretis) provided. Insert screwdriver orjam-breaker wrench into left side of a disposer mounting lug at the top of the drsposer. Turn the power switch to the OFF position before attempting to clear a jam or remove an object from the disposer, When attempting to loosen a jam In a waster disposer, use a self service jambreaker wrench as described in Use and Care Guide. When attempting to remove objects from a waster disposer, use lony-handled tongs or pliers. Before pressing red reset button, be sure the wall switch is In the off position and on batch feed models remove the stopper from the run position. b. [. . . ]