User manual VOLTCRAFT DT-20LK

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual VOLTCRAFT DT-20LK. We hope that this VOLTCRAFT DT-20LK user guide will be useful to you.


VOLTCRAFT DT-20LK : Download the complete user guide (1767 Ko)

Manual abstract: user guide VOLTCRAFT DT-20LK

Detailed instructions for use are in the User's Guide.

[. . . ] On the back of the adapter holder, there is a small reflector strip on a black surface. Thus, check the adapter holder before each use and, if required, replace the reflector strip. You can overwrite old measurement values by selecting any memory location, starting the measurement and saving the values as described above. In order to preserve, protect and improve the quality of environment, protect human health and utilise natural resources prudently and rationally, the user should return unserviceable product to relevant facilities in accordance with statutory regulations. [. . . ] Therefore only the provided self-adhesive reflective markers are to be used for measuring. ⷠIf the laser caution label placed on the device should not be printed in your language use the provided laser caution labels in the respective language. Release the MEM button when the required memory location appears on the display (bottom right). You find more information on saving measurement data in the section "Saving / reading measurement data". Then press the MODE button repeatedly until the display (top) shows the required display unit. Sequence 1 sequence 2 function RPM REV RPM = Revolutions per minute (contactless) rPm = Revolutions per minute (contact, with cone) rPm M HZ = Frequency (contactless + contact, with cone) M/M = Metres per minute (contact, with cone) HZ In I/M = Inch per minute (contact, with cone) F/M = Feet per minute (contact, with cone) M/M FT Y/M = Yard per minute (contact, with cone) I/M Yd REV = Total number of revolutions (contactless + contact, with cone) M = Total distance in metres (contact, with friction wheel) F/M In = Total distance in inches (contact, with friction wheel) FT = Total distance in feet (contact, with friction wheel) Y/M Yd = Total distance in yards (contact, with friction wheel) The battery should be removed from the device if it is not used for a long period of time to avoid damage through leaking. Leaking or damaged batteries might cause acid burns when in contact with skin, therefore use suitable protective gloves to handle corrupted batteries. Do not leave the battery lying around, as there is risk, that children or pets swallow it. ⷠBatteries must not be dismantled, short-circuited or thrown into fire. Batteries/ rechargeable batteries containing hazardous substances are marked with the crossed-out wheeled bin. You can return used batteries/ rechargeable batteries free of charge to any collecting point of your local authority, our stores or where batteries/ rechargeable batteries are sold. Consequently you comply with your legal obligations and contribute to environmental protection!Repair works must only be carried out by a specialist/ specialist workshop. ⷠIf you have queries about handling the device, that are not answered in this operating instruction, our technical support is available under the following address and telephone number: Voltcraft®, 92242 Hirschau, Lindenweg 15, Germany, phone 0180 / 586 582 7 We do not assume liability for resulting damages to property or personal injury if the product has been abused in any way or damaged by improper use or failure to observe these operating instructions. Carefully read the whole operating instructions before operating the device, otherwise there is risk of danger. The distance between measurement device and reflector strip should be 5 - 50 cm. the top right-hand side of the display will show HOLD and the measurement value will be frozen on the display. in such a case , attach several reflector strips at equal distances on the object under measurement. Then divide the measurement result by the number of reflector strips to arrive at the correct measurement result. ⷠWhen used in conjunction with other devices, observe the operating instructions and safety notices of connected devices. [. . . ] Rotating parts must always come to a complete standstill and must be secured against being switched on again before attaching any reflector strip. The non-reflecting area must always be larger than the reflector strip. a single data set consists of four measurement values (last displayed value of the measurement process , maximum value (MAX) , minimal value (MIN) and average value (AVG). At the end of a measurement process, press the MEM button while pressing and holding the MEAS button. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE VOLTCRAFT DT-20LK




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual VOLTCRAFT DT-20LK will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.