Detailed instructions for use are in the User's Guide.
[. . . ] US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.
MODE KEYS allow you to select which device your remote will operate. They are also used to setup the remote control POWER used in conjunction with the device Keys, the Power key lets you turn devices on and off
POWER
UF4-200C
4-in-1 Cable TV Remote Control
VISIT US ON THE WEB
You can find programming instructions and codes for all of our remote controls, as well as information about our other products on our website:
TV
CABLE
HELP displays the on-screen help system
AUX
VCR
LOCK allows restricting viewing of certain programs MUTE turns volume off
MUTE VOL
www. uselectronics. com
2
INSTALL BATTERIES
EXIT exits out of on-screen menus FOUR-WAY CURSOR KEYS allow you to navigate through the on-screen menus OK/SELECT chooses the highlighted item in the menu GUIDE displays the program guide PAGE moves the menu forward and backward one page DAY-, DAY+ move the on-screen guide backward and forward by one day
HELP
LOCK
EXIT
INFO
VOL turns the volume up and down INFO displays channel and program information
Before you can program or operate the remote control, you must install two Alkaline AA batteries. Step 1: Remove the battery compartment cover on the back of your remote control. [. . . ] If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScanTM section later in this manual.
e
Write the codes below Cable Box code ____ ____ ____ VCR Code ____ ____ ____ TV code ____ ____ ____ Aux. code ____ ____ ____
7 MASTER POWER CONTROL
You can program your UF4-200C to turn on and off all of your remote-controlled devices (TV, CABLE, AUX, VCR) when you press POWER. All devices must be in direct line of sight to ensure proper operation. Perform the following steps to enable or disable power control for each device:
UP YOUR 5 SETTINGAUXILIARYREMOTE FOR AN DEVICE
You can program the AUX key to control an auxiliary device such as a second remote-controlled TV or VCR, a Motorola satellite receiver, or a digital audio tuner.
b c d
Make sure all devices to be controlled are turned on. Press and hold any mode key (AUX, CABLE, TV, or VCR) for approximately three seconds until all four mode keys flash twice. The selected mode key will flash three times and turn off.
b c d
Look up the device manufacturer in the Device Codes section and note the code. Press and release the AUX key for approximately three seconds until the four mode keys flash twice. On the remote control, press and release the appropriate mode key for the device (VCR for a video cassette recorder, TV for a television, and CABLE for a cable device). The AUX key will stop flashing and will stay lit continuously until you complete step 4) Enter the three-digit code for your TV, VCR or Cable device. After you press the first digit, the AUX key should light and stay on. After you press the last digit, the AUX key should flash three times and turn off. If the AUX key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code.
8 CHANNEL LOCK
Channel Lock prevents the channel up and down functions from operating any device other than the cable box -- no matter which device (AUX, CABLE, TV, or VCR) is currently selected. If you want the remote control to operate channel functions on your TV, VCR, or Auxiliary device, you will need to de-activate Channel lock. To de-activate Channel Lock, follow these steps:
e
f
Point the remote at the device and press the POWER key. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScanTM section later in this manual.
b c
Press and hold the CABLE key for 3 seconds. If you are sure the batteries are good, try rolling them with your finger (while they are in the remote control) to ensure a good connection. Finally, make sure that nothing is blocking the signal from the remote control from reaching your TV, VCR, or Cable Converter; and make sure that you are pointing the remote control at the correct device when you are pressing a key on the remote.
If none of the codes listed for your Cable Box, TV, or VCR works, the CodeScanTM method will allow you to cycle through all the available codes in the remote until you find the right Cable Box, TV, or VCR code. Manually turn on power to the device for which you want to program the remote (TV, CABLE, AUX, VCR). Press and hold a mode key for approximately three seconds until the four mode keys flash twice. [. . . ] Count and record the sequence of flashes to determine the three-digit code.
y Problem buttons only operate my cable box. Follow the steps in section 8 to disengage Make sure
Channel Lock.
d
y Problem The Video-on-Demand keys don't work. x Solution Video-on-Demand (VOD) keys, the remote control must be in cable mode. Press To use the
the cable button when you want the VOD keys to operate VOD functions. [. . . ]