User manual TYAN THUNDER TOMCAT H1000E

[. . . ] Thunder h1000E Tomcat h1000E /// Version 1. 1 S3970 Copyright Copyright © TYAN Computer Corporation, 2006. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Taro and Thunder h1000E / Tomcat h1000E are trademarks of TYAN Computer Corporation. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Allows user to force BIOS/Option ROM of add-on cards to be displayed during quiet boot. Selects Power-on state for Numlock. Quiet Boot Enabled Add On ROM Display Mode Boot up Num-Lock Force BIOS Keep Current On Off Enabled Disabled Auto Enabled Disabled Hit ` DEL'Message Display Enabled Disabled Interrupt 19 Capture Disabled Enabled PS/2 Mouse Support Selects support for PS/2 Mouse. Wait for ` If Error F1' Waits for F1 key to be present if error occurs. Enabled: allows option ROMs to trap interrupt 19. 63 http://www. tyan. com 3. 7. 2 ­ Boot Device Priority Sub-Menu Use this screen to select options for the Boot Device Priority. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Boot Device Priority 1st Boot Device 2nd Boot Device [xx, xxx-xxxxx:xxx] [xx, xxx-xxxxx:xxx] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu. ¡ö ¡÷ Select Screen ¡ô¡õ Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature Boot Device Priority 1st Boot Device 2nd Boot Device Option xx, xxx-xxxxx:xxx xx, xxx-xxxxx:xxx Disabled Description Settings for boot priority. These can be customized depending on your preference. 64 http://www. tyan. com 3. 7. 3 ­ Hard Disk Drives Sub-Menu Use this screen to select options for the hard disk Drives. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Hard Disk Drives 1st Drive [xxxxxxxxxxxxxxxxxx] Specifies the boot sequence from the available devices. ¡ö ¡÷ Select Screen ¡ô¡õ Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature Removable Drives Option Description xx, xxx-xxxxx:xxx 1st Drive Disabled Specifies the boot sequence for the available devices. 65 http://www. tyan. com 3. 7. 4 ­ Removable Drives Sub-Menu Use this screen to select options for the Removable Drives. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Removable Drives 1st Drive [xxxxxxxxxxxxxxxxxx] Specifies the boot sequence from the available devices. ¡ö ¡÷ Select Screen ¡ô¡õ Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature Removable Drives Option Description xx, xxx-xxxxx:xxx 1st Drive Disabled Specifies the boot sequence for removable drive booting. This option will show all removable devices. 66 http://www. tyan. com 3. 8 ­ BIOS Security Menu The system can be configured so that all users must enter a password every time the system boots or when BIOS Setup is entered, using either the Supervisor password or User password. The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password. If you forget it, you must clear CMOS and reconfigure. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Security Settings Install or change the password. Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Boot Sector Virus Protection [Disabled] ¡ö ¡÷ Select Screen ¡ô¡õ Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature Security Settings Supervisor Password: Option Description If the password has been set, Installed displays. When it is set to [Enabled], BIOS will issue a virus warning message and beep if a write to the boot sector or the partition table of the HDD is attempted. Not Installed Installed User Password: Change Supervisor Password Change User Password Not Installed Installed Disabled Boot Sector Virus Protection Enabled 67 http://www. tyan. com 3. 9 ­ BIOS Chipset Menu This menu allows the user to customize functions of the AMD Chipsets. North Bridge configuration contains options for Memory & CPU settings. Additional configuration for the AMD8131 PCI-X Tunnel is available in the PCI-X Configuration Menu. Select a menu by highlighting it using the Arrow (á/â) keys and pressing Enter. The settings are described on the following pages. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit 4 NorthBridge Configuration 4 HT1000 South Bridge Configuration Options for NB. ¡ö ¡÷ Select Screen ¡ô¡õ Select Item +/- Change Option Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit 68 http://www. tyan. com 3. 9. 1 ­ North Bridge Chipset Configuration Sub-Menu This menu gives options for customizing memory & Hypertransport settings. Select a menu by highlighting it using the Arrow (á/â) keys and pressing Enter. The settings are described on the following pages. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit NorthBridge Chipset Configuration ¡ö ¡÷ Select Screen ¡ô¡õ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit :XXX MHz :XX :X CLK :X CLK :X CLK :X CLK :XX CLK :X ns 4 Memory Configuration 4 ECC Configuration 4 IOMMU Option Configuration Memory CLK CAS latency (Tcl) RAS/CAS Delay (Trcd) Min Active RAS (Tras) Row Precharge Time (Trp) RAS/RAS Delay (Trrd) Row Cycle (Trc) Asynchronous Latency Feature Option NorthBridge Chipset Configuration Memory CLK Read only Description It shows the clock frequency of the installed SDRAM. CAS Latency (Tcl) Read only This controls the timing delay (in clock cycles) before SDRAM starts a read command after receiving it. When DRAM is refreshed, both rows and columns are addressed separately. This setup item allows you to determine the timing of the transition from RAS (row address strobe) to CAS (column address strobe). [. . . ] The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. 92 http://www. tyan. com Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a dealer near you, you can bring your system to them to have it serviced instead of attempting to do so yourself (which can have expensive consequences). [. . . ]