User manual TYAN THUNDER K8QW

[. . . ] Thunder K8QW /// Revision 1. 01 S4881G2NR Copyright © TYAN Computer Corporation, 2005-2006. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] PhoenixBIOS Setup Utility LAN Control Enable LAN [Enabled] Item Specific Help 51 http://www. TYAN. com Enable LAN1 OPROM Enable LAN1 OPROM [Enabled] [disabled] F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values PCI/PNP ISA UMB Region Exclusion You can use this screen to select options for the PCI/PNP ISA UMB Region Exclusion settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility PCI/PNP ISA UMB Region Exclusion C800-CBFF: CC00-CFFF: D000-D3FF: D400-D7FF: D800-DBFF: DC00-DFFF: [Available] [Available] [Available] [Available] [Available] [Available] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature C800-CBFF, CC00-CFFF D000-D3FF, D400-D7FF D800-D8FF, DC00-DFFF Option Available Reserved Description Reserves the specified block of upper memory for use by legacy ISA devices. 52 http://www. TYAN. com PCI/PNP ISA IRQ Resource Exclusion You can use this screen to select options for the PCI/PNP IRQ Resource Exclusion settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility PCI/PNP ISA IRQ Resource Exclusion IRQ3 IRQ4 IRQ5: IRQ7 IRQ9 IRQ10 IRQ11 IRQ15 Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature IRQ3/4/5/7/9/10/11/15 Option Available Reserved Description Reserves the specified IRQ for use by legacy ISA devices. 3. 4. 4 - IDE Configuration Sub-Menu You can use this screen to select options for the IDE Configuration settings. Use the <Plus> and <Minus> keys to change the value of the selected option. 53 http://www. TYAN. com PhoenixBIOS Setup Utility IDE Configuration Sub-Menu Large Disk Access Mode: SMART Device Monitoring: Local Bus IDE adapter: Primary Master Primary Slave Secondary Master Secondary Slave [Dos] [Disabled] [Both] Item Specific Help Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Large Disk Access Mode SMART Device Monitoring Local Bus IDE adapter Option DOS Other Disabled Enabled Both Disabled Primary Secondary Menu Item Menu Item Description Select the IDE access mode. Configure the IDE channel. Primary Master/Slave Secondary Master/Slave Primary Master/Slave, Secondary Master/Slave The following screen shows the information of IDE device. PhoenixBIOS Setup Utility 54 http://www. TYAN. com Primary Master/Slave, Secondary Master/Slave Type: Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: [Auto] [Disabled] [Disabled] [Disabled] [Standard] [Disabled] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Multi-Sector Transfers Option Disabled Enabled Disabled Description Specify the number of sectors per block for multiple sector transfer. Enabling LBA causes Logical Block Addressing to be used in place of Cylinders, Heads_Sectors. Select the Ultra DMA mode used for moving data to/from the drive. LBA Mode Control Enabled Disabled 32 Bit I/O Enabled Standard Transfer Mode Fast PIO 1 Disabled Ultra DMA Mode Enabled 55 http://www. TYAN. com 3. 4. 5 - Floppy Configuration Sub-Menu You can use this screen to select options for the Floppy Configuration settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Floppy Configuration Sub-Menu Legacy Diskette A: Legacy Diskette B: [1. 44/1. 25MB 3 1/2''] [Disabled] Item Specific Help Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Legacy Diskette A/B Option Disabled 1 360kb 5 /4'' 1. 2MB 51/4'' 720kb 31/2'' 1. 44/1. 25 MB 1 3 /2'' 1 2. 88MB 3 /2'' Description Select floppy type 3. 4. 6 - I/O Device Configuration Sub-Menu You can use this screen to select options for the I/O Device Configuration settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility I/O Device Configuration Sub-Menu Serial port A: [Auto] Item Specific Help 56 http://www. TYAN. com Serial port B: Mode: Parallel port: Mode: Floppy disk controller: Base I/O address [Auto] [Normal] [Auto] [ECP] [Disabled] [Primary] F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Serial port A Serial port B Mode Parallel port Mode Floppy disk controller Base I/O address Option Auto Disabled Auto Disabled Normal IR ASK-IR Auto Disabled Output Only Bi-directional EPP ECP Enabled Disabled Auto Primary Secondary Description Configure serial port A using options. Set the base I/O address for parallel port. 3. 4. 7- Hardware Monitor Sub-Menu You can use this screen to hardware monitor infomation. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Hardware Monitor Sub-Menu 57 http://www. TYAN. com CPUx Temperature Sysx VRM temperature CPUx Fan Speed System Fanx Speed CPUx VDD Voltage +12V +12V CPU Board +5v +5v CPU Board +3. 3V AMD8131 Vcore 1. 8V CK804 Vcore 1. 5V xxC xxC xxxxRPM xxxxRPM x. x V x. xV x. xV x. xV x. xV x. xV x. xV x. xV Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values 3. 4. 8 ­ Console Redirection Sub-Menu You can use this screen to select options for the Console Redirection settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Console Redirection Sub-Menu Com Port Address Baud Rate Console Type Flow Control Console connection Continue C. R. after POST [Disabled] [19. 2] [PC-ANSI] [CTS/RTS] [Direct] [off] Item Specific Help 58 http://www. TYAN. com F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Com Port Address Baud Rate Console Type Flow Control Option Disabled On-board COMA On-board COMB 300 1200 2400 9600 19. 2K 38. 4K 57. 6K 115. 2K VT100 VT100, 8bit PCI-ANSI, 7bit PCI-ANSI VT100+ VT-UTF8 CTS/RTS XON/XOFF None Direct Description Select the Com Port address. Enable the specified baud rate. Enable the specified console type. Enable flow control. Indicate whether the console is connected directly to the system or a modem is used to connect. [. . . ] 99h Check for SMART Drive (optional) 9Ah Shadow option ROMs 9Ch Set up Power Management 9Dh Initialize security engine (optional) 9Eh Enable hardware interrupts 9Fh Determine number of ATA and SCSI drives A0h Set time of day A2h Check key lock A4h Initialize Typematic rate A8h Erase F2 prompt AAh Scan for F2 key stroke ACh Enter SETUP AEh Clear Boot flag B0h Check for errors B2h POST done - prepare to boot operating system Code Beeps / Description BAh Initialize DMI parameters BBh Initialize PnP Option ROMs BCh BDh BEh BFh C0h C1h C2h C3h C4h C5h C6h C7h C8h C9h D2h E0h E1h E2h E3h E4h E5h E6h E7h E8h E9h EAh EBh ECh EDh EEh EFh F0h F1h F2h F3h F4h Clear parity checkers Display MultiBoot menu Clear screen (optional) Check virus and backup reminders Try to boot with INT 19 Initialize POST Error Manager (PEM) Initialize error logging Initialize error display function Initialize system error handler PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional) Unknown interrupt Initialize the chipset Initialize the bridge Initialize the CPU Initialize system timer Initialize system I/O Check force recovery boot Checksum BIOS ROM Go to BIOS Set Huge Segment Initialize Multi Processor Initialize OEM special code Initialize PIC and DMA Initialize Memory type Initialize Memory size Shadow Boot Block System memory test Initialize interrupt vectors Initialize Run Time Clock Initialize video Initialize System Management Mode Output one beep before boot 75 http://www. TYAN. com Code B4h B5h B6h B9h Beeps / Description One short beep before boot Terminate QuietBoot (optional) Check password (optional) Prepare Boot Code Beeps / Description F5h Boot to Mini DOS F6h Clear Huge Segment F7h Boot to Full DOS 76 http://www. TYAN. com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Furthermore, if you purchased your system from a dealer near you, take the system to them directly to have it serviced instead of attempting to do so yourself (which can have expensive consequences). If these options are not available for you then Tyan Computer Corporation can help. [. . . ]