User manual TP-LINK TL-SG3424P

[. . . ] 0 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1: About this User's Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 1 Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 2 Assumpsit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Caution: Between the remote management software and the telnet management described in the next chapter, you can only choose one to manage the switch. 5. 1 Steps of Installation of the Remote Management Software --SSU 1) 2) Installation requirement: Windows OS, Supporting TCP/IP Protocol. Installation steps: Run the setup. exe, and following the wizard to finish the setup. If you want to change the default path, click Browse, Input or choose the path you want, click OK and then next to finish the setup. As figure 5-1. Figure 5-1 5. 2 Usage of Remote Configuration Software -- SSU The interface of SSU application is friendly and easy to use. Generally speaking, there -8- TL-SG3424P/TL-SL2226P+ are four steps on configuring the switch. 1) 2) 3) 4) Add Connection Configuration Exit Remote Smart Switch User Guide Caution: When you use the switch for the first time, you must reset the IP address and gateway of the switch. The witch default IP address is 192. 168. 0. 100(for more details, please refer to Chapter 5). Before configuration, make sure that the PC and the switch which the SSU application installed can see each other. If they can't see each other, check whether the power is on and the twisted pair is well connected. If all is ok, run the SSU application, you can see the initialized interface of the SSU application. As figure 5-2. Figure 5-2 5. 2. 1 Add 1) First, add a device group. As figure 5-16. Figure 5-16 Now you can configure each parameter of the port except port priority. auto-test the speed and negotiate the duplex mode with the - 17 - TL-SG3424P/TL-SL2226P+ 10HD: 10Mbps, Half-Duplex. 100FD: 100Mbps, Full-Duplex 2) Flow Control: Remote Smart Switch User Guide Disable: The port won't produce Flow Control packets and will discard the Flow Control packets received. Enable: The Switch will negotiate Flow Control on the specified port according to Full-Duplex or Half-Duplex. 3) Port Security: When you configure the Port Security of a port to be Enable, the port won't learn any new MAC address. Furthermore, the port only transfers the data accordant to static MAC Address. If the port does not bind any static MAC address, the port will not transfer data. When the Port Security of a port is disabled, the port will automatically learn any new MAC Address and transfer data. Default setting: Disable 4) Default PVID: There is the choice only in the IEEE802. 1Q Tag VLAN mode. Every port on the Switch has a default VID which is the VID for an untag Tag received by the port. Default Value: 1 User Info: User Info just gives the port a description. [. . . ] The interface of VLAN Mode is as follows. - 26 - TL-SG3424P/TL-SL2226P+ Remote Smart Switch User Guide Figure 6-8 Port Based VLAN is as follows. Figure 6-9 Only if current VLAN Mode is Port Based VLAN, you can see this interface, or you will see an error message. 802. 1Q VLAN is as follows. - 27 - TL-SG3424P/TL-SL2226P+ Remote Smart Switch User Guide Figure 6-10 Only if the VLAN Mode is 802. 1Q VLAN, you can see this interface, or you will see an error massage. TRUNK Management TRUNK Management interface as follows: Figure 6-11 Before you enable a TRUNK, you must make the properties of the 4 ports be the same. If you synchronously configure VLAN, in a VLAN, the four ports must exist or be deleted at the same time. [. . . ]