User manual TP-LINK TG-5269

[. . . ] http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] 2 Main Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2 2. 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 1. 1 2. 1. 2 Install driver for XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Update driver for XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Appendix A: Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Package contents The following items should be found in your package: One 10/100/1000Mbps Gigabit Ethernet PC Card One Resource CD, including: Drivers This User Guide Other Helpful Information Note: If any of the listed contents are damaged or missing, please contact the retailer from whom you purchased the 10/100/1000Mbps Gigabit Ethernet PC Card for assistance. The Card or TG-5269 mentioned in this guide stands for 10/100/1000Mbps Gigabit Ethernet PC Card. 1 TG-5269 10/100/1000Mbps Gigabit Ethernet PC Card User Guide Chapter 1 Introduction Thank you for choosing the TG-5269 10/100/1000Mbps Gigabit Ethernet PC Card! 1. 1 Product Overview The Card is a highly integrated and cost-effective Gigabit Ethernet Card that provides 32-bit performance, Cardbus controller, and full compliance with IEEE 802. 3 10Base-T, IEEE 802. 3u 100Base-TX, IEEE 802. ab 1000Base-T specifications and IEEE 802. 3x Full Duplex Flow. It is the easiest way to upgrade a network from 10M to 100M and 1000Mbps. Supports 10Mbps, 100Mbps and 1000Mbps network speed both in Half-Duplex and Full-Duplex transfer modes, using Auto-Negotiation technology to detect the network speed. It also can be widely used in most modern Operating System. 1. 2 Main Features Supports IEEE 802. 3, IEEE 802. 3u, IEEE 802. 3ab Complies with 32-bit CardBus standard and PC Card type II standard 68 pin PC Card standard connector, 1 RJ45 port (Auto MD/MDIX) 10/100/1000M Auto-Negotiation, Full-Duplex and Half-Duplex Auto-Detect Supports Ethernet frame with VLAN Tag Supports receiving and transmitting jumbo frames Supports hot-swappable Supports Win9x/ME/2000/XP/Vista, Netware 3. x/4. x/5. x , Linux etc 1. 3 LED Status The 1000M Link/Act LED of TG-5269 indicates Link/Act status when the Card works in the 1000M mode. It will light when connection is built, and glitter when the Card is transmitting or receiving data. The 100M Link/Act of TG-5269 indicates Link/Act status when the Card is working in the 100M mode. It will light when connection is built, and glitter when the Card is transmitting or receiving data. 2 TG-5269 10/100/1000Mbps Gigabit Ethernet PC Card User Guide Chapter 2 Installation 2. 1 Hardware Installation To install the Card, follow these steps as below: Step 1: Locate an available CardBus slot on your laptop. Step 2: With the connector pin end facing the CardBus slot and the label facing up, slide the Card into the CardBus slot until it locks in place. [. . . ] And the driver installation for Windows XP completes. 8 TG-5269 10/100/1000Mbps Gigabit Ethernet PC Card User Guide Figure 2-11 2. 1. 2 Update driver for XP If the "Welcome to the Found New Hardware Wizard" screen does not appear after you insert the Card, you can follow the steps below to install the driver, and you can also upgrade the latest driver available on the CD-ROM in this way. Step 1: Right click "My Computer" icon on the desktop and select "Properties" (show in Figure 2-12). Figure 2-12 Step 2: Select "Hardware" and then "Device Manager" in the next screen (shown in Figure 2-13). 9 TG-5269 10/100/1000Mbps Gigabit Ethernet PC Card User Guide Figure 2-13 Step 3: Right click "TP-LINK 10/100/1000Mbps Gigabit Ethernet PC Card", and then select "Update Driver. . . " in Figure 2-14. (Note: If the driver was installed correctly, you may see "Ethernet Controller" instead. [. . . ]