Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL
3LCD DATA PROJECTOR TLP-S10
(SVGA)
Others
Maintenance
Operations
Preparations
Before Using
Before Using
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold with USA only this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] Let everyone involved with the use of the projector know that. fact.
To audio output Audio cable (for computer) (supplied) To RGB output RGB cable (supplied)
AUDIO MONITOR COMPUTER( Y/PB/PR ) VIDEO VIDEO S-VIDEO CONTROL
Projection Distance and Screen Size
Use the figures, tables, and formulas below to determine the screen size and projection distance. (Screen sizes are approximate values for full-size picture with no keystone adjustment) As seen from above
Screen
Monitor cable Mini D-sub 15P-BNC (not supplied)
a=
projection size (inches) 0. 8668 25. 81
Audio cable (supplied)
To Y/CB/CR output Green (Y) Blue (CB), Red (CR)
S-Video cable (not supplied) Control cable Video cable (supplied)
90·<
As seen from the side
Lens center
90·<
screen size projection distance a (m) (cm) 40 (102) 1. 52 60 (152) 2. 29 80 (203) 3. 07 100 (254) 3. 84 150 (381) 5. 78 200 (508) 7. 72 250 (635) 9. 65 300 (762) 11. 59
Yellow (to video output)
To audio
To audio output White (L) Red (R)
Conversion output adapter White (L) Red (R) BNC-pin (not supplied)
p. 40
To S-Video output To RS-232C terminal
DVD player
VCR
Computer (for control)
a
Note
· The AUDIO terminal can be used with all the devices for input terminal.
a is the distance (m) between the lens and the screen, and corresponds to a range of 1. 52 m to 11. 59 m.
18
19
Preparations
Operations
Turning the power on and off
Connecting the power cord
Turning the power off
1 2
Insert the power cord connector into the AC IN socket of the projector. Insert the power cord plug into a wall or other power outlet.
When the power cord is plugged in, the following three green indicators will come on for several seconds: ON, TEMP, and LAMP. Next, the ON indicator will change to orange, indicating standby mode. (Do not perform any operations while the 3 green indicators are on. )
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. (This operation is no longer valid after the message disappears. )
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode.
When cooling lamp
FAN
(Green)
During internal cooling
FAN
(Green)
After cooling is completed
FAN
(Off)
(Supplied) Power cord connector
TEMP LAMP
ON
TEMP LAMP
(Off)
ON
(Orange)
TEMP LAMP
(Off)
ON
(Orange)
Removing the lens cover
Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat.
(Green) (Orange) Flashing
A
B
C
A B
During cooling, the LAMP indicator flashes. In addition, unplugging the power cord in this state will shorten the life of the lamp. After the LAMP indicator goes off, the cooling fan continues to operate for a short while in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord in this state. In standby mode.
I Turning the power on
Press the ON/STANDBY button.
The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the startup screen appears.
Control panel
FAN TEMP LAMP ON INPUT ON / STANDBY
ZOOM+
Remote Control
CALL ON/ STANDBY KEYSTONE AUTOSET
Start-up screen
C
Note
MUTE
FREEZE
MENU
RESIZE
· The projector consumes about 6W of power in standby. We recommend you to unplug the power cord if you will not use the projector for an extended period.
VOL. +
CANCEL
PRECAUTIONS
INPUT
KEYSTONE
ZOOM-
AUTO SET
WARNING
· Do not look into the lens during operation. Doing so could damage your vision.
· Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging the power cord and cutting off the power while the projector is running or being cooled will shorten the life of the lamp. However, please unplug the power cord if the projector locks up or acts abnormally. · If the power cord was unplugged before cooling was complete, give the lamp sufficient time to cool before plugging it back in. If the lamp overheats, it may fail to light, and its lifetime will be shortened.
CAUTION
· Do not block the air intake or exhaust. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object.
LCD Panels
LCD panels wear out. [. . . ] one minute of abnormal display, the projector returns to the standby state waiting for internal cool down.
(Orange (Red lit) flashing)
PRECAUTIONS
· Make sure to unplug the power cord if something goes wrong. · If the power cord is unplugged before cooling is complete, give the lamp enough time to cool before plugging it back in. Unplugging the power cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if you are not concerned about lamp lifetime, the light may not come on if you do not wait at least 3 minutes. )
Used Lamps
This projector's lamps contain trace amounts of environmentally harmful inorganic mercury. [. . . ]