User manual TASCAM M-106

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user's authority to operate this equipment. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. For the customers in Europe WARNING This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. [. . . ] By connecting the SUB OUTPUTS to a recorder, you can record the same stereo mix signal as it is output from an amplification or speaker system. Connect mics to the channel 1­6 MIC input jacks (XLR). When using condenser mics that require phantom power, turn the PHANTOM (+48V) switch on the rear panel ON. Connect mics to MIC (1-6) · Use the PHANTOM (+48V) switch to turn the phantom power supply to all channels (1­6) ON or OFF simultaneously. When the PHANTOM (+48V) switch is ON, if you want to use dynamic mics at the same time as condenser mics, always connect the dynamic mics using balanced connections. TASCAM M-164/M-164FX/M-106 15 3 - Preparation for Use CAUTION · Connecting a dynamic mic with an unbalanced connection could damage it if the PHANTOM (+48V) switch is ON. Do not connect or disconnect mics when the PHANTOM (+48V) switch is ON. When the PHANTOM (+48V) switch is ON (and the mixer power is ON) the +48V indicator lights on the right side of the meter panel. The XLR connector #2 pins are "hot" on this mixer. ª Channels 11-12 · Connect a stereo sound source using RCA pin jack jacks (L, R). · On M-106 mixers, the stereo audio output from a computer connected by USB is also input to channels 11-12. The signals from these channels can also be sent to AUX 1. · · ª Channels 13-14 · · Connect a stereo sound source using standard jacks (L, R). These jacks are balanced, but they can also be connected with unbalanced sound sources. · If a mono sound source is connected to the L jack, the L input signal is sent to both channels 13 and 14. Connecting synthesizers, other sound sources and audio equipment (line level sound sources) Line level sound sources can be connected to every channel (1­16). However, the types of jacks and mixer functions differ depending on the channel. Failure to do so might cause noise that could damage the equipment. Turning on the power 1 Turn the mixer power ON using the ON/STANDBY switch on the rear panel of the mixer. The indicator on the right of the meter panel lights. TASCAM M-164/M-164FX/M-106 17 4 - Using the mixer Adjusting levels After turning on the power, adjust the level of each input signal. The following explanation assumes that the STEREO OUTPUTS are being used as the main outputs. 1 Prepare headphones or an amplification system to output the sound in advance. If monitoring with headphones, raise the volume with the PHONES LEVEL knob slightly. If monitoring with an amplification system, raise the input level on the amp slightly. 3 Raise the ST (stereo) fader to the 0 position. 4 For the channel 1­6 inputs, adjust the TRIM knob for the channel so that the "0" indicator on the channel level meter lights when a signal is being input that is at the loudest level ordinarily expected. For the channel 7­16 inputs, adjust the level at the sound source so that the "0" indicator on the channel level meter lights when a signal is being input that is at the loudest level ordinarily expected. Input channel level meter 2 Turn the MONITOR section ST switch ON (push switch in). With this set, the level of the signals output from the STEREO OUTPUTS jacks is shown on the MONITOR meters. 18 TASCAM M-164/M-164FX/M-106 4 - Using the mixer 5 Raise the channel fader. Using the mixer channel functions High-pass filter (HPF) Press the HPF switch to turn the high-pass filter ON and cut frequencies of 80 Hz or less by ­12 dB/octave. The high-pass filter affects inputs from both MIC and LINE input jacks, but it is especially effective when using mics for reducing unwanted noise from wind and breathing. CAUTION Even if there is no meter indication or no signal is being output despite the fact that a signal is being input, do not raise the faders carelessly. The operation of other switches or features could cause a loud signal to be output suddenly, possibly damaging speakers or other equipment. [. . . ] The next screen appears. Moreover, the alteration or addition of computer hardware peripherals might improve the computer's ability to process audio as well as increase the number of tracks that it can record simultaneously. TASCAM M-164/M-164FX/M-106 29 5 - Using with a Computer (M-106) Control panel settings Overview M-106 functions can be set from the control panel. On Windows XP, the M-106 Control Panel can be accessed from shortcuts in the following locations. Connecting by USB Use the included USB cable to connect the M-106 with a computer as shown in the illustration. · Start menu · Control panels · Programs/TASCAM/M-106 On Mac OS X, the M-106 Control Panel is located inside the application folder. The control panel is divided into the following two sections. USB Computer · Status display section CAUTION Some USB equipment uses the USB bus frequently. In order to prevent the audio signal from dropping out, clicking noises and other trouble, we recommend that you do not connect other USB equipment (including USB hubs) to the same USB hub to which the M-106 is connected. [. . . ]