User manual SYMPHONIC TVCR19F1

[. . . ] This warranty shall not be extended to any other person or transferee. This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any the product not purchased and used in the United States. This warranty only covers failures due to defects in material or workmanship which occurs during normal use. [. . . ] This will prevent damage to the TV due to lightning and power-line surges. Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Infrared Sensor Window- Receives the infrared control signals from the remote control unit. CHANNEL NUMBER buttons- Press two digits to directly access the desired channel. +100 button- Press to select cable channels which are equal or greater than number 100. 10. MUTE button- Press the MUTE button to turn off the sound portion of the TV program. (Volume level display turns LIGHT RED from LIGHT BLUE. ) Press the MUTE button again or press the VOL(ume) L or M button to restore sound. 11. CHANNEL RETURN button- Press this button to go back to the previously viewed channel. For example, pressing the CHANNEL RETURN button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it second time will return from CH 10 to CH 3. G The TV may recognize TV channels to be CATV channels by the receiving conditions. In this case, try AUTO PRESET CH action again in the fine receiving conditions. G When AUTO PRESET CH is activated where there is no TV signal input, "NO TV SIGNALS" will appear on the display after the completion of the channel scanning. [ADD/DELETE FUNCTION] 1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the CH(annel) L or M button to point to "CHANNEL SET". 3) Press the VOL(ume) L button so that "ADD/DELETE" is selected. 4) Use the CH(annel) L or M button to select the channel you wish to put into memory or to erase from memory. Perform "ADD/DELETE" function while this display appears on the screen. G Press the VOL(ume) L or M button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory. G Press the VOL(ume) L or M button to light up the channel number in LIGHT RED if you wish to erase the channel from memory. 5) Press the MENU button to exit the menu. ADD/DELETE AUTO PRESET CH PICTURE CHANNEL SET [ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF] PICTURE CHANNEL SET [ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF] CHANNEL PRESETTING NOTE:You MUST PRESET channels BEFORE using CHANNEL L orM button. [. . . ] Also, the lower rating will turn [VIEW] automatically. TV RATING MPAA RATING G When you turn "TV-Y" to [BLOCK] or [VIEW], the all ratings will turn to [BLOCK] or [VIEW] automatically. G When you turn "TV-MA" to [VIEW], the all ratings will turn to [VIEW] automatically. G PG PG-13 R NC-17 X [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] When you select TV-Y7, TV-PG, TV-14, or TV-MA and you press the VOL(ume) L button, the sub-ratings will appear on the TV screen. If you select the rating category (example: TV-PG) and turn it [BLOCK] or [VIEW], the sub-ratings (example: V for Violence) will turn [BLOCK] or [VIEW] automatically. You can set the sub-ratings to [BLOCK] or [VIEW] individually when the [BLOCK] rating category is set to [BLOCK]. FV [BLOCK] Press the CH(annel) L or M button to select "FV" (Fantasy Violence). [. . . ]