User manual SYLVANIA 6240CVA

[. . . ] · The RF output channel will change to channel 4 from channel 3 and you will and start the playback again. ton on the VCR for 3 seconds · When a picture does not appear on the TV screen, repeat step [4]. 5) Press the STOP button to stop playback. Stereo TV Connection You can use the AUDIO OUT jack and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. Please refer to your TV's owner's manual. VIDEO IN AUDIO IN L R ANT IN AUDIO OUT IN OUT VIDEO Disconnect 2 Connect Audio/Video Cables (not supplied) ANT IN VIDEO OUT AUDIO OUT OUT 3 Connect (supplied) L R (Back of TV) Connect 1 OUT (Back of VCR) RF Cable Front & Rear Terminals AUDIO OUT jack Connect the audio cable to the audio in jack of a camcorder, another VCR, a stereo amplifier, or an audio system. [. . . ] Preset for Use Turn on the VCR for the first time To Add/Delete Channels Clock Set Up 1 Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see"RF Output Channel" section. To Select a Channel You can select a channel by directly pressing the Number buttons on the remote control. Notes for using the Number buttons: · When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press 1, 1, 7) · You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). 1 MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT 1 MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT 5 STOP PLAY CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : ­­ AM/PM ­­ or STOP PLAY STOP PLAY or or 2 POWER Remote Control TV Screen LANGUAGE SELECT B ENGLISH STOP PLAY F. FWD · If the clock is not set, the CLOCK SET screen appears when you press the MENU button. In this case, go to step [2]. F. FWD Select the current hour F. FWD [ON] 6 STOP PLAY CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : 40 AM/PM ­­ FRANCAIS ESPAÑOL 2 STOP PLAY CHANNEL SET UP AUTO SET UP B MANUAL SET UP or or To Preset the Channel Again 1) Press the MENU button until the main menu appears. 2) Select "CHANNEL SET UP" by pressing the PLAY or STOP button. 3) Select "AUTO SET UP" by pressing the PLAY or STOP button. Finally, press the C. RESET/EXIT button. Select "ADD" or "DELETE" Select the current year F. FWD Hint · Repeat these steps only if there was a power failure or if the VCR has been unplugged for more than 30 seconds. 5 To exit the menu. Precautions Precautions Install Location For safety and optimum performance of your VCR: · Install the VCR in a horizontal and stable position. · Shield it from direct sunlight and keep it away from sources of intense heat. Avoid places with insufficient ventilation for proper heat dissipation. Avoid locations subject to strong vibration or strong magnetic fields. Important Copyright Information Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright laws. Other Operations 1 POWER To cue or review picture during playback (Picture Search) Press the F. FWD or REW button. · Press it again and the VCR will now search in super high speed. (in the LP/SLP modes only) To play back in slow motion Press the SLOW button during playback or the still mode. · If the noise bar appears on the TV screen, you can reduce it by pressing the CHANNEL buttons. 4 EJECT VCR / TV 1 4 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL 1 POWER VCR/TV 2 PLAY TAPE IN Remote Control TV Screen 7 MENU SEARCH -MODE CHANNEL MENU REC/OTR STOP/EJECT REW PLAY F. FWD C. RESET EXIT POWER VCR/TV TAPE IN TIMER REC PLAYB REC/OTR DISPLAY PAUSE /STILL To freeze the picture on TV screen during playback (Still mode) Press the PAUSE/STILL button. Each time you press the button, the picture will be forwarded by one frame. · If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing the CHANNEL buttons. · If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if equipped. To temporarily stop recording (Pause mode) Press the PAUSE/STILL button. · During the rec pause mode, five C marks appear on the TV screen. · Press it again to resume recording. REW STOP PLAY F. FWD 3 STOP 4 EJECT STOP 3 Hint EJECT A 2 32 4 · When a tape without record tab is inserted, the VCR will start playback automatically at step [1]. To adjust the tracking manually, press the CHANNEL buttons. Auto Rewind When a tape reaches its end during playback, fast-forward, or recording (except timer recording and One Touch Recording), the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and turn itself to off. Counter Reset Press the C. RESET/EXIT button. 6. [. . . ] THIS WARRANTY IS VALID WHEN THE PRODPARTS: FUNAI CORPORATION will provide UCT IS DELIVERED PREPAID TO A FUNAI AUTHOparts to replace defective parts without RIZED SERVICE FACILITY. charge for a period of one (1) year from IMPORTANT: the date of original retail purchase. THIS LIMITED WARRANTY GIVES YOU SPECIFIC Certain parts are excluded from this LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS warranty. THAT VARY FROM STATE TO STATE, IF AT ANY TIME LIMITS AND EXCLUSIONS: DURING THE WARRANTY PERIOD YOU ARE UNABLE THIS WARRANTY IS EXTENDED ONLY TO THE ORIGI- TO OBTAIN SATISFACTION WITH THE EXCHANGE NAL RETAIL PURCHASER. [. . . ]