Detailed instructions for use are in the User's Guide.
[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
PRECAUCION
RIESGO DE CHOQUE ELECTRICO NO ABRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Reorient or relocate the receiving antennas. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Cycles through the Multi-channel TV Sound (MTS) options: Stereo, Mono, and Auto SAP (Second Audio Program). The TV alternates between current channel and the last channel that was selected. Press for a direct selection of Effect settings (Simulated, Surround, Off). Press the arrow buttons to move the cursor, then press the center button to select or access an option. Turns the TV off automatically in approximately 15, 30, 45, 60, or 90 minutes. Cancel by pressing until Sleep off appears.
3 MTS/SAP A B C
MUTING DISPLAY POWER
J 4 JUMP
MTS/SAP
TV/VIDEO
K
1 4 7
D E F G H I
RESET
2 5 8 0
VOL
3 6 9
ENT
CH
L5
PICTURE MODE
JUMP
PICTURE MODE
6 VOL (volume) 7 M 8
MENU
N 9 RESET
SLEEP
O q; POWER
RM-Y194
qa TV/VIDEO
TV
qs
and ENTER
0 9
qd CH (channel) qf MENU qg SLEEP
If you lose your remote control, see page 34.
3
Connecting Your TV
Read this section before setting up your TV for the first time. This section covers basic connections in addition to any optional equipment you may be connecting.
TV Rear Panel
Connections
1 4 2
3
Jack
1 S VIDEO
Description Connects to the S VIDEO OUT jack on your VCR or other video equipment that has S VIDEO. S VIDEO provides better picture quality than the VHF/UHF jacks or the video input jack. S VIDEO does not provide sound; the audio cables must still be connected.
S-VIDEO is only for KV-24FS120.
2 VHF/UHF 3 Video/Audio
Connects to your VHF/UHF antenna or cable. Connects to the AUDIO and VIDEO output jacks on your VCR or other video equipment. A second video input jack (VIDEO 2) is located on the front panel of the TV. Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV.
Optional Connection
To view from the satellite receiver or VCR, select the video input to which your satellite receiver or VCR is connected by pressing on the remote control.
11
Connecting a DVD Player using Composite Video (Video/Audio L(Mono), R)
Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your DVD player to AUDIO/VIDEO IN on your TV.
Rear of TV Rear of DVD Player
Connections
Optional connection
Video (yellow) Audio L (white) Audio R (red)
Optional connection
For better picture quality, use S VIDEO instead of the yellow audio/video cable. S-VIDEO does not provide sound, so you still must connect the audio cables. If your DVD player is equipped with component video outputs (Y, PB, PR/L, R), you can improve the picture quality by using component video cables (480i only).
Connecting a DVD Player using Component Video (Y, PB, PR)
Rear of TV Rear of DVD Player
PR (red) PB (blue) Y (green)
Audio L (white) Audio R (red)
2
1
1 2
Using component video cables (not supplied), connect the Y, PB, PR OUT on your DVD player to Y, PB, PR IN on your TV. Connect AUDIO OUT on your DVD player to AUDIO IN on your TV.
The Y, PB, PR outputs on your DVD player are sometimes labeled Y, CB, and CR or Y, B-Y, and R-Y. If so, connect the cables to like colors.
12
Connecting Headphones
Connect the headphones to the jack on the front of your TV. Headphone jack is STEREO.
Front A/V Panel
Connections
Connecting a Camcorder
Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your camcorder to AUDIO and VIDEO IN on your TV.
Front A/V Panel
A/V output
Audio R (red) Audio L (white) Video (yellow)
13
Connecting for Video Tape Editing (VCR and Camcorder)
Camcorder
(for playback)
1b
Rear of TV
Connections
A/V output
VCR (for playback)
Video (yellow) Audio L (white) Audio R (red)
1a
VCR (for recording) 2
1
For video tape editing connect to the VCR the following sources (VCR or Camcorder): a) Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your first VCR to AUDIO/VIDEO IN on your second VCR b) Using audio/video cables (not supplied), connect the AUDIO/VIDEO OUT on your Camcorder to the AUDIO/VIDEO IN on your second VCR
2
Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on the second VCR to the AUDIO/VIDEO IN on your TV.
14
Using Basic Functions
Setting Up the TV
After you have finished connecting your TV, you can use Auto Program to set up your channels. During Auto Program, the TV will automatically search for available channels and program receivable channels.
1
When you start Auto Program wait until it is finished; otherwise it will skip over channels that are available. Perform Auto Program again to program receivable channels.
Press
to turn on the TV. The Initial Setup screen appears.
Initial Setup
Basic Functions
First please connect cable/antenna Auto Program [CH+] [CH] Exit
2
Press on the remote control or on the TV front panel to start Auto Program, or press to exit.
The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.
1 2 3 4 5 6 1 2 3 4
To perform Auto Program again Press . Press Press F or f to highlight On or Off according to how you connected your TV. Release .
15
Quick Start to the Menus
The following settings are available in your on-screen menus: Menu Allows you to
Video: Vivid Picture Brightness Color Hue Sharpness
Video Mode : Vivid Picture Controls Color Temp. [. . . ] Press g to open the Video Label menu: 1 Press F or f to access the input you want to label and press . 2 Press F or f to choose a label and press Press g to open Tilt Correction: Press F or f to correct any tilt of the picture from 5 to +5, then press activate and return to the Setup menu. to
Info Banner
Video Label Label connected equipment
Menus
Tilt Correction Language 16:9 Enhanced
Provides enhanced picture resolution for wide-screen sources such as DVD. This is only available when the TV is in Video mode.
31
Other Information
Troubleshooting
If you have a problem with your TV, try the suggestions below. [. . . ]