User manual SMEG CWC621SD

[. . . ] THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE, TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON-ORIGINAL SPARE PARTS. THE APPLIANCE MUST BE IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEE). BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT. [. . . ] The earth wire (PE) is yellow-green in colour, the neutral wire (N) is blue and the live wires (L1, L2, L3) are black, grey and brown. In the event of single-phase connection (230V-1N~) the connection to the electrical mains must be made using a cable with plug compliant with the relevant regulations. . 5 FIRST START-UP The electrical protection system must undergo a functional test before the appliance is put into operation. The appliance must be installed and/or inspected by the qualified staff, who will start it up for the first time and provide the relevant operating instructions. PREPARING FOR USE Important: The rinse aid dispenser is fitted on all models, the detergent dispenser only on some. If both dispensers are present put the external detergent and rinse aid containers in place and insert the respective intake hoses on the rear of the machine into them. Red hose: detergent blue hose: rinse aid Before inserting the hoses into the containers, fit the weights (needed to ensure that they always draw in liquid from the bottoms of the containers) and the filters onto their ends as shown. If the detergent dispenser is not factory-fitted, it can be by ordering the relative kit. As an alternative an external dispenser can be fitted, making the electrical connection by means of an H05 RN-F 2x0. 5 mm electrical cable, which can be laid along the route shown in the TECHNICAL DATA diagram and connected as shown in the wiring diagram supplied with the dishwasher. The dispenser must operate on 230V/50 Hz with maximum power absorption of 15 W. Connect to the detergent dispenser outside the dishwasher using the red hose mentioned above. IMPORTANT: Whenever the type of detergent or rinse aid is changed, it is ABSOLUTELY ESSENTIAL to flush out the peristaltic pumps by placing the external intake pipes in water for a few cycles. Always use only products specifically recommended for use in a dishwasher. Comply carefully with the instructions provided by the detergent producer on the pack. Turn on the mains water tap (user) Check: The level of detergent and That the filters are in place, rinse aid in the containers. the spray arms rotate, and there are no foreign bodies in the dishwasher. Switch on the master switch (user): the word "OFF" appears on the display. 8. 3 FIRST USE EACH DAY (tank and boiler empty) off; green; orange; flashing. Actions and what happens With the door closed: Press and hold it down the dishwasher fills the tank after the water in the boiler has heated up; light L2 shows orange and the boiler heating element symbol appears on the display. Wait for P1 to appear and LED L1 to change from orange to green; the tank heating element comes on until the set temperature is reached. The duration of this stage may vary depending on the mains water temperature and on the single-phase connection. Press the button to display the tank (left) and boiler (right) temperatures. Load the dishes Indicator lights as follows: Display shows Select the program required by pressing . and holding it Confirm the program start by pressing down for 1 second (light L2 changes from green to orange). 13 Cycle in progress, the time left until the end of the cycle is displayed. If the door is opened "CLOSE" flashes and the program stops; when it is closed again the program restarts from the beginning. At the end of the program "End" flashes Unload the dishes When the door is closed again, the last program is repeated. 8. 4 Program change With the door closed, to change to a fresh program instead of repeating the last one, press the button. [. . . ] Never switch the dishwasher off with water in the tank; pump out first. 11 MAINTENANCE AND CLEANING Although no particular scheduled maintenance is required, users are advised to have the dishwasher checked by a specialist technician twice a year. N. B. : the manufacturer accepts no liability for wilful damage or damage deriving from carelessness, neglect, failure to comply with instructions, regulations and standards or incorrect connections. 11. 1 Daily cleaning The dishwasher has IPX4 protection, but the use of direct water jets for cleaning is forbidden. Cleaning the filter during the day In case of particularly heavy-duty working conditions, the filter should be cleaned every 30-40 cycles, keeping the machine in operating conditions; to do this, carry out the "partial tank pump-out" routine (program "P0"). Press the button, and hold it down, until "P0" and the duration of 1' appear on the display. Confirm by pressing ; light L2 turns orange. At the end of the pump-out the word "End" flashes on the display. Close the door again to start filling the tank prior to performance of a new wash cycle. [. . . ]