User manual SANYO LNS-W11 LENS REPLACEMENT PROCEDURE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANYO LNS-W11. We hope that this SANYO LNS-W11 user guide will be useful to you.
Manual abstract: user guide SANYO LNS-W11LENS REPLACEMENT PROCEDURE
Detailed instructions for use are in the User's Guide.
[. . . ] LCD Projector Lens Replacement Procedure
Model Number
LNS-T10/LNS-W10/LNS-T11/LNS-W11 AH-23541/AH-23511/AH-23661/AH-23631
Notes on Lens Replacement
Lens replacement should be performed by the qualified service personnel. Before an attempt to replace the lens, confirm the model number (both the LCD projector and the lens) and prepare the proper lens. When installing or removing the lens, be careful not to stain, scratch or damage the lens. [. . . ] Turn the Lens Cover counter-clockwise and pull it toward front to remove the Lens Cover. Remove the two screws (SCREW "A") and remove the Top Cabinet.
TOP CABINET SCREW "A"
LENS COVER
Fig-1-1
SCREW "A"
1. Remove the two screws (SCREW "A") and remove the Top Cabinet.
TOP CABINET
LENS COVER
Fig-1-2
2
Remove the Light-Block Sheet Base
Slide the Light-Block Sheet Base upward to remove it.
LIGHT-BLOCK SHEET BASE
Fig-2
-3-
3
Remove the Lens
Push the Lens Lock Lever and turn the lens counterclockwise (1/4 turn) and then take it out. Be careful not to drop the lens.
LENS LOCK LEVER
Fig-3
4
Mount the Lens 1. {When LNS-W11 (AH-23631) is installed, the Light Block Sheet is unnecessary. } 3. Insert the lens into the Lens Bracket of the projector as matching the red mark on the lens to that on the Lens Bracket. Turn the lens clockwise until the lens is locked with Lens Lock Lever.
LENS BRACKET
Insert the lens into the Lens Bracket as matching these marks.
Fig-4
-4-
5
Mount the Light-Block Sheet Base
Mount the Light-Block Sheet Base.
LIGHT-BLOCK SHEET BASE
HOOKS
LIGHT-BLOCK SHEET
Light-Block Sheet should be located under the hooks. HOOKS
Fig-5
6
Mount the Top Cabinet and the Lens Cover
For the Cabinet Fig. Position the mark "UP" of the Lens Cover on top and push into the cabinet. {When LNS-W11 (AH-23631) is installed, the Lens Cover is unnecessary. } For the Cabinet Fig. {When LNS-W11 (AH-23631) is installed, the Lens Cover is unnecessary. }
Turn the projector on and check Lens shift, Zoom and Focus is operating properly. If Light-Block Sheet interfere with those operations, check if the Light-Block Sheet is set properly. LNS-W11 (AH-23631) cannot adjust the Zoom and Focus at the Remote control or the projector.
UP
Fig-6-1
Fig-6-2
-5-
Focus Adjustment
{For LNS-W11 (AH-23631)}
Set up the projector in the place where it is to be used, turn on the power and project a picture. The focus at the edges of the screen may not be as sharp as at the center of the screen. If the focus cannot be set correctly at the center of the screen, it will be necessary to move the lens unit forward or back relative to the flange in order to adjust the back focus. Turn the fixing roulette about 1/4 of a turn counterclockwise to release it. [. . . ] Check that the focus at the center of the screen is correct, and then turn the fixing roulette clockwise until it is tightened securely. Check that the focus ring is still turned counterclockwise as far as it will go at this time. Return the projector to its original setup location and repeat steps 1 and 2 to adjust the focus.
PIN FOCUS RING FLANGE
ROULETTE
NOTE: Please remove 3 pins when you install it in the cabinet of B type.
-6- [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SANYO LNS-W11
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANYO LNS-W11 will begin.