Detailed instructions for use are in the User's Guide.
[. . . ] Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The instructions for use shall specify the maximum mass or dry cloth in kg, for which the appliance is designed. If the appliance is supplied from a cord extension set or electrical portable outlet device the cord extension set or electrical portable outlet device should be positioned so it is not subject to splashing or ingress of moisture.
2
DESCRIPTION OF PARTS
LID
Be sure to keep the lid closed during washing and spinning.
WATER SUPPLY HOSE(HOT)
WATER SUPPLY HOSE (COLD) DRAIN-HOSE (PUMP) FABRIC SOFTENER DISPENSER SPIN BASKET
Stainless
BLEACH INLET
"CENTER-JET" PULSATOR POWER CORD
MAGIC FILTER
Lint will be collected in the filter during washing.
SOUND ABSORPTION PANEL
FRONT CONTROL PANEL
GROUND LEAD
When the water pipe is metal, make sure to cover the end of the ground wire.
ADJUSTABLE LEGS
Adjust the length of the legs when installing the washer.
WATER DRAIN HOSE
3
CONTROL PANEL
1. Press once again to turn the washer off.
6.
WATER LEVEL SELECT BUTTON
According to the washload, select the water level ;
MEDIUM¡HIGH¡EXTRA LOW¡LOW
START/HOLD BUTTON
Use to pause and restart the operation. [. . . ] Press once again to turn the washer off.
6.
WATER LEVEL SELECT BUTTON
According to the washload, select the water level ;
MEDIUM¡HIGH¡EXTRA LOW¡LOW
START/HOLD BUTTON
Use to pause and restart the operation. To change the washing procedure during operation, press this button to stop, and once again to restart after changing the procedure.
7.
WATER SUPPLY SELECT BUTTON
As you press this button, the type of water is selected as follows.
COLD¡COLD+HOT¡HOT¡COLD
3. 4.
DELAY START BUTTON
Press this button when delay start washing is needed.
8.
REMAINING TIME INDICATOR LIGHT
The indicator light shows the remaining time (in minutes) of each wash cycle. At the end of the cycle, the power automatically switches off.
COURSE SELECT BUTTON
With every press of this button, the washing course changes;
FUZZY¡HEAVY¡SPEEDY¡WOOL¡SAREE¡FUZZY
9.
FUNCTION INDICATOR LIGHT
The function in use indicator shows the current function as a flashing symbol. The light goes out at the end of the function.
5.
FUNCTION SELECT BUTTON
With every press of this button, the function changes; SOAK, WASH, RINSE, SPIN¡WASH ¡RINSE¡SPIN¡
WASH&RINSE¡RINSE&SPIN¡WASH, RINSE, SPIN
4
WASHING PROCEDURE
Before starting washing, check the following;
Connect the water supply hose to the water tap. Make sure to lay down the drain hose. (In case no drain pump)
Put the laundry into the washer and add detergent, too.
Be careful not to overload. Use right detergent for the fabrics you are washing.
FUZZY COURSE Selects the best washing course automatically.
1. Press the POWER Button to"ON".
POWER
HEAVY COURSE
1. Press the power button to "ON".
POWER
2. Washing, rinsing, and spinning follow.
If you want to pause, press the START/HOLD button again. You can change the course when paused.
3. Washing, rinsing, and spinning follow.
If you want to pause, press the START/HOLD button again. You can change the course when paused.
START/HOLD
START/HOLD
3. Press the START/HOLD button once.
Washing and rinsing go on for 38 minutes. When the FUNCTION button is pressed during working, the rinse times can be changed to between 1 and 5 times in duration.
Function Button
five times
RINSE AND SPIN
Press the FUNCTION button six times. Rinsing and spin drying follow.
When the FUNCTION button is pressed during working, the rinse times can be changed to between 1 and 5 times in duration.
Function Button
six times
6
INSTALLATION & MAINTENANCE
ENVIRONMENT
Leave some space
Maintain at least 10cm between the washer and the wall.
ASSEMBLING THE SOUND ABSORBING PANEL
Tilt the washer a little and lift up the panel until it clicks, filnaly fix the panel with screw to the base as shown in the figure.
Rear-side
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface, noise or vibration occurs. Never install the washer near water.
Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard.
CONNECTING THE DRAIN HOSE
After pressing the joint ring(a), insert the drain hose(b) to drain direction. (a)
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight.
IN CASE OF PUMP-DRAINED WASHER
qTake out the q Be sure to join tightly q Install the drain
(b)
LEVELLING
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB. q Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. q Place the machine more than 10cm away from the wall.
cap-hose and connect the outlet-hose.
the drain hose into the hose in the position drain-outlet on theback of about 70~80cm of the machine. above the ground.
cap-hose
outlet-hose
70~80cm
q Adjust the legs on feet for levelling .
Loosen
Lock
CONNECTING THE WATER SUPPLY HOSE
1. Remove the adaptor from the water supply hose. Pull down the part (c) of the water supply hose . When the part (c)is released, the hose is automatically connected to the adaptor making a 'click' sound. 5. Connect the other end of the water supply hose to the inlet water valve at the back of the washer. [. . . ] above the ground.
cap-hose
outlet-hose
70~80cm
q Adjust the legs on feet for levelling .
Loosen
Lock
CONNECTING THE WATER SUPPLY HOSE
1. Remove the adaptor from the water supply hose. Pull down the part (c) of the water supply hose . When the part (c)is released, the hose is automatically connected to the adaptor making a 'click' sound. 5. Connect the other end of the water supply hose to the inlet water valve at the back of the washer. If the water tap is a screw type, assemble a water supply hose that fits to the tap as shown.
2. First, using a "+" type screw driver, loosen the four screws on the adaptor. [. . . ]