User manual SAMSUNG SU3350

[. . . ] · Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. Empty dirt cup and clean filter frequently when picking up very fine materials such as powder. · Do not use to pick up flammable or combustible materials such as gasoline or fine wood, fine wood sandings or use in areas where they may be present. · Store your vacuum cleaner indoors, in a cool and dry area. 2_ safety information Safety information · Avoid picking up hard, sharp objects with the cleaner. [. . . ] Tighten securely with a screwdriver. 01 ASSEMbLING THE cLEANER ATTAcH DUST bIN TO VAcUUM Fit the groove located on the lower front side of the Dust Bin to the hook located on the vacuum body and attach the hook located on the Dust Bin Handle to the vacuum body as shown. ATTAcH VAcUUM HOSE AND TOOLS 1. Attach the Twist Snap Hose by lining up the taps on the base with the corresponding notches on the back of the vacuum as shown. Grasping the Hose Wand, slide the end of the it onto the Hose Wand Base. Snap the Hose into the Hose Clip. Note: The vacuum will not operate effectively unless the Hose Wand is firmly attached. 4. Attach the Lower Cord Wrap by lining up the tab on the base with the corresponding notch on the back of the vacuum and turn it clockwise as shown. Attach the Extension Wand and the Crevice Tool together into the holder on the right side of the body as shown. Attach the Combination Tool into the holder on the left side of the body as shown. Attach the Bracket Brush on the front of the handle and clip the Mini Turbo Brush into the Bracket Brush as shown. * Select Models Only assembling the cleaner _7 Operating the cleaner pOwER SwITcH The Power Switch is located on the side of the vacuum. Push the rocker switch "ON" to vacuum, and "OFF" when cleaning is complete. HANDLE pOSITIONS Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions. 1. Upright ­ For storage and above floor cleaning with tools. 2. ­ With the vacuum in normal cleaning position, press handle release pedal again. Use for reaching under low furniture such as tables, chairs or beds. HEIGHT ADjUSTMENT The Powerfoot/Rotating Floor Brush can be adjusted to clean several floor surfaces. Note : For optimal cleaning performance, adjust to the lowest practical setting. If your cleaner is difficult to push, adjust to the next higher setting. Always ensure that the correct height setting is used for your flooring type as damage may occur if the height setting is not changed to reflect your flooring type. Turn Height Adjustment Knob to desired setting. Bare floor Setting ­ For bare floors. Medium Settings Highest Setting ­ For short and medium pile carpets. To move your cleaner from room to room, put the Handle in the upright position, tilt the cleaner back on its rear wheels and push forward. The cleaner can also be moved by using the Carrying Handle located on the top of the Dust Bin. Carrying Handle 8_ operating the cleaner Operating the cleaner SpEcIAL ON-bOARD TOOLS Your vacuum is not only a powerful carpet and rug cleaner, it's also a versatile above floor vacuum cleaner when you select one of the special tools. Grasp the end of the Hose Wand and lift Hose Wand to separate from the Hose Wand Base. Attach tools by firmly pushing onto Vacuum Hose Quick Release Cord Wrap or Extension Wand. Crevice Tool combination Dusting brush/Upholstery Tool: Power Cord Two Types of cleaning tools are included in one attachment: rotate for desired tool. Extension Wand · Use Brush side to dust furniture, blinds, books, lamps, shelves, and baseboards. [. . . ] If properly installed, Drive Belt will center itself on Rotating Brush crown. Insert the hook on the Brush Cover into the corresponding groove on the brush and tighten scerws securely. Hook WARNING Be careful of your hands when you replace the drive belt, to avoide physical injury from sharp plastic film. 12_ maintenance Maintenance MINI TURbO bRUSH brushbar Replacement 1. With the curved ends facing down, slide end plates of brushbar into slots on the tool. To replace bottom plate, insert the four tabs on edge of bottom plate into slots on front of tool. [. . . ]