User manual SAMSUNG SMH1713W/XAC INSTALLATION GUIDE INSTALLATION MANUAL

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SAMSUNG SMH1713W/XAC. We hope that this SAMSUNG SMH1713W/XAC user guide will be useful to you.


SAMSUNG SMH1713W/XAC INSTALLATION GUIDE INSTALLATION MANUAL: Download the complete user guide (9056 Ko)

You may also download the following manuals related to this product:

   SAMSUNG SMH1713W/XAC (5909 ko)
   SAMSUNG SMH1713W/XAC (5909 ko)

Manual abstract: user guide SAMSUNG SMH1713W/XACINSTALLATION GUIDE INSTALLATION MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] INSTALLATION INSTRUCTIONS OVER THE RANGE MICROWAVE OVEN BEFORE YOU BEGIN (Read these instructions completely and carefully. ) IMPORTANT IMPORTANT • • • • • Save these instructions for local inspector’s use. Note to Installer - Be sure to leave these instructions with the Consumer. skill level - Installation of this appliance requires basic mechanical and electrical skills. [. . . ] C L 30 to Cooktop Draw a vertical line on the wall at the center of the 30 space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom cabinet frame. Plate position – beneath recessed bottom cabinet with front overhang Draw a line on the back wall equal to the depth of the front overhang. Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level. If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. Draw a horizontal line on the back wall an equal C L 30" to Cooktop distance below the cabinet bottom as the inside depth of the front overhang. For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D. ALIGNING THE WALL PLATE Hole A Centerline notches Draw a Vertical Line on Wall from Center of Top Cabinet C L Horizontal Line Area E Hole B Horizontal Line Draw a Horizontal line on wall from bottom of “Rear Wall Template”. CAUTION: Wear gloves to avoid cutting CAUTION: Wear gloves to avoid cutting fingers on sharp fingers on sharp edges. Draw a Vertical line on the wall at the center of the 30" wide space. Draw a Horizontal line on the wall at the bottom of “Rear Wall Template”. Drill 5/8" holes for toggle bolts on 3 locations (Hole A, Hole B, Hole C) but if the location of hole is same as that of stud, drill a 3/16" hole for wood screw. If none of A, B and C is in a stud, find a stud somewhere in area E and draw a forth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) Recirculating (Non-Vented Ductless) Outside Back Exhaust (Horizontal Duct) NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). Select the type of ventilation required for your installation and proceed to that section. Attach Mounting Plate to Wall Prepare Top Cabinet Mount the Microwave Oven Adjust the Exhaust Adaptor Connecting Ductwork A1. ATTACH THE MOUNTING PLATE TO THE WALL NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. [. . . ] At least one wood screw must be used to attach the plate to a wall stud. Insert the bolts into the mounting plate through the To use toggle bolts: Spacing for Toggles More Than Wall Thickness Mounting Plate Toggle Wings Toggle Bolt holes designated to go into drywall and reattach the toggle wings to ¾” onto each bolt. €¢ Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SAMSUNG SMH1713W/XAC




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SAMSUNG SMH1713W/XAC will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.