User manual SAMSUNG NC220P

[. . . ] SyncMaster NC220P LED Monitor User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Table Of Contents MAJOR SAFETY PRECAUTIONS Before You Start . 6-3 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) . 6-4 1 1-1 Major Safety Precautions Before You Start Icons used in this manual ICON NAME Caution MEANING Indicates cases where the function may not work or the setting may be canceled. Note Indicates a hint or tip to operate a function. Using this Manual · · Make yourself fully aware of the safety precautions before using this product. If a problem occurs, refer to the 'Troubleshooting' section. Copyright Notice The contents of this manual are subject to change without prior notice for performance improvement. Copyright © 2011 Samsung Electronics Co. , Ltd. [. . . ] In this case, move the screen so that the screen is displayed at the center of the display panel using the <H-Position> menu. Fine If you cannot remove the noise completely with the <Fine> function, adjust the <Coarse> and then use the <Fine> function again. This function is only available in <Analog> mode. COLOR 3-8 Using the product Menu Description Expresses natural colors more clearly without changing the picture quality by using proprietary digital picture quality improvement technology developed by Samsung Electronics. Color · · · · <Off> - Turns the < Color> function off. Color> with the original pictures. <Demo> - You can compare the pictures processed by < <Full> - Provides a clearer picture including areas corresponding to skin color. <Intelligent> - Improves the chroma of pictures except for areas corresponding to skin color. You can adjust the red color value according to your preference. Red This menu is unavailable when < Color> is set to <Full> mode or <Intelligent> mode. You can adjust the green color value according to your preference. Green This menu is unavailable when < Color> is set to <Full> mode or <Intelligent> mode. You can adjust the blue color value according to your preference. Blue This menu is unavailable when < Color> is set to <Full> mode or <Intelligent> mode. You can set the color temperature according to your preference. · · · Color Tone · · <Cool 2> - Sets the color temperature of the screen to very cool. <Normal> - Sets the color temperature of the screen to the standard color temperature. <Warm 2> - Sets the color temperature of the screen to very warm. · <Custom> - Select this menu to set the color temperature manually. If you do not like the preset color temperatures, you can manually adjust the value of RGB. · This menu is unavailable when < Color> is set to <Full> mode or <Intelligent> mode. Gamma Using this menu, you can change the intensity of the colors of medium brightness. · <Mode1> - <Mode2> - <Mode3> This is unavailable when < Bright> is set to <Dynamic Contrast> or <Cinema> mode. SIZE & POSITION Using the product 3-8 Menu Description Moves the position of the display area on the screen horizontally. H-Position This function is only available in <Analog> mode. Moves the position of the display area on the screen vertically. V-Position This function is only available in <Analog> mode. You can adjust the vertical position of the OSD. Menu H-Position Menu V-Position SETUP&RESET Menu Reset Description Use this function to restore the visual quality and color settings to the factory defaults. · <No> - <Yes> Select a language for the OSD. Language The selected language is only applied to the product OSD. Display Time You can determine the time to wait before the OSD is hidden. · Menu Transparency <5 sec> - <10 sec> - < 20 sec> - <200 sec> You can select the transparency of the OSD. · <Off> - <On> 3-8 Using the product INFORMATION Menu Description Shows the frequency and resolution set on the PC. INFORMATION For models with an Analog interface only, <Analog/Digital> is not shown in the <Information>. Using the product 3-8 4 4-1 Installing the Software PCoIP On Screen Display (OSD) The On Screen Display (OSD) local GUI is displayed to the user when the device is powered on and a PCoIP session is not in progress. The OSD provides a mechanism to connect to a host device via the Connect Screen. The Options Window is accessible through the <Options> button on the Connect Screen. [. . . ] Windows Vista : Change the frequency by selecting Control Panel Appearance and Personalization Personalization Display settings Advanced settings Monitor, and then change the refresh rate under Monitor Settings. Windows 7 : Change the frequency by selecting Control Panel Appearance and Personalization Display Adjust resolution Advanced settings Monitor, and then change the refresh rate under Monitor Settings. (For more information, refer to the User Manual of the computer or the graphics card. ) How can I change the resolution?Windows XP : Change the resolution by selecting Control Panel Appearance and Themes Display Settings. [. . . ]