User manual SAGEM D20V

[. . . ] août 2005 11:46 11 User guide LU 252117222C_D20V_EN. book Page 2 Mercredi, 24. août 2005 11:46 11 INTRODUCTION Dear customer: Thank you for purchasing a Sagem Commnication DECT telephone; we appreciate your trust in us. This product was manufactured with the upmost care, should you encounter any difficulties during its use, we recommend that you refer to this user guide. You can also find information on the following site: http://www. sagem. com/faq For your comfort and safety, we ask that you read the following paragraph carefully: Recommendations and safety instructions Your DECT telephone must not be installed in a humid room (wash room, bathroom, laundry room, kitchen, etc. ) unless it is 1. 50 m away from a water point, or outside. [. . . ] To exit the menu, press the red key . When you re-initialise the base, the base code becomes 0000 again and the voice box number must be reprogrammed. "Modifying the voice box number", page 21. 24 LU 252117222C_D20V_EN. book Page 25 Mercredi, 24. août 2005 11:46 11 REGISTRATION REGISTRATION Five SAGEM D20 handsets can be logged on to one base station. On the base: Put the base to which you want to link the telephone set in registration mode and press the base button for several seconds. The green light blinks rapidly, the base is in link mode during 3 minutes maximum. Once the handset is registered, you will hear an acoustic signal and the number assigned to the handset is displayed at the left of the screen. If the handset put out an irregular acoustic signal, pairing has aborted. Disconnect and re-connect the power supply cord of the base and repeat the procedure. Press . Registering an additional handset to a base To register an additional handset to a base you must: · put the handset in registration mode, · put the base in registration mode. Once this is done, the registration (mutual recognition of the base and the new handset) will be done automatically (registration can take a few seconds). Pick up the handset which you want to register: On the navigator key , press or until the REGISTRATION screen is displayed, press OK to confirm. Select the base station number by pressing a corresponding key (1, 2, 3 or 4). Enter the code of the base station (0000 by default setting) which the handset is to be registered on to. The handset enters the registration mode. Modifying the base preference This function enables you to specify which base will be used by your handset to make calls (if your handset is registered to several bases). On the navigator key , press or until the REGISTRATION screen is displayed, press OK to confirm. 25 LU 252117222C_D20V_EN. book Page 26 Mercredi, 24. août 2005 11:46 11 REGISTRATION Select SELECT BASE using OK. Press Regardless of the number of handsets registered, the number 1 to 5 will scroll on the screen. To exit the menu, press the red key . Select the base preference by pressing the or key. You cannot select the base preference if the handset is not registered on it. The symbol onto the base number indicates that the base can be selected. To exit the menu, press the red key . De-registering a handset This function enables you to de-register a handset from your base. This may be necessary if you have lost a handset or if you already have 5 handsets registered to the same base. To de-register the handset from the base, you must do the following on another handset registered to the same base. On the navigator key , press or until the REGISTRATION screen is displayed, press OK to confirm. [. . . ] If you are registering a new handset to your D20 base, (refer to paragraph Registering an additional handset to a base, page 25). Your handset is not registered on a base, (refer to paragraph Registering an additional handset to a base, page 25). Note: When the handset is not registered on a base, you can only access to the REGISTRATION menu. Inopportune ringing When the messages in the voice box have been consulted, the message presence indicators are turned off by the service provider. [. . . ]