User manual SAGEM AXIUM HD D45

[. . . ] Anglais LU 45 A5. qxd 06/10/2004 10:25 Page 1 TABLE OF CONTENTS 1. 1. 1. Safety Maintenance 2 3 Precautions Set Up Fitting the speaker columns (optional) Aerial connection Mains connection Switch on Switching off your SAGEM AXIUMTM Home Cinema Screen 4 4 5 5 5 2 4 1. 1. 1. 2. 5. Respect all maintenance advice, safety precautions and instructions recommended in this user booklet are for your safety and to prolong the working life of the equipment. Buttons the right side door Front panel indicator lights and remote control receiver 6 7 First Rapid Installation Description of the buttons and indicator lights Remote Control Personalised settings Changing the security code Return to initial configuration Searching TV programmes Choice of country Manual installation Automatic installation Modifying the programme list Choose the MENU language Setting for the economy mode Setting for the SPDIF output Adjusting the headphones output Setting the speaker mode Adjusting the Hi-Fi output Exit stanby mode tuning 6 6 7 8 8 8 8 8 9 9 9 10 10 10 11 11 11 11 Warning concerning user and equipment safety. 5. [. . . ] For better comfort of listening to your audio system, cut the sound of your SAGEM AXIUMTM Home Cinema Screen (see § 6. 8). The DLPTM technology causes a slight delay in picture processing, so connect your amplifier to these sockets and not to those of the source (see § 6. 9) PC2 IN SPDIF IN Recommended for connecting a PC or a DVD player equipped with "DVI D" socket. Only use a "DVI D" cable (graphics card). The DLPTM technology causes a slight delay in picture processing. To synchronize the sound with your SAGEM AXIUMTM Home Cinema Screen, connect the digital audio output of your DVD player to this output and recover the synchronized signal on SPDIF OUT. SPDIF OUT This output allows you to recover the signal sent to SPDIF IN after digital synchronization with the picture. Connect this output to the digital audio input of your Home Cinema audio amplifier. 11 12 Anglais LU 45 A5. qxd 06/10/2004 10:25 Page 13 RIGHT SIDE DOOR IMAGE OK STBY 7. 3. Configuration of computer sources AUDIO OPTIONS INSTALL. HEADPHONES CODE V- V+ recommended for headphones. Adjusting the headphones is covered in § 6. 7. SOURCES PC DATA If a personal computer is used (PC or MAC), switch on your SAGEM AXIUMTM Home Cinema Screen before the computer. HORIZONTAL VERTICAL FREQUENCY PROTECTION PP+ 0 0 0 Press the MENU button, then choose "INSTALL" using the button and validate with OK. CHANNEL MAN. PHASE EPG AUTO IMAGE YES 0 Choose "PC DATA" then validate with OK. AUDIO A V 6 AV6 recommended when connecting a camcorder in VHS, S-VHS, 8 mm, Hi-8 or digital DVC format. Resolution (px) 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 Frequency (Hz) 60 66 72 75 85 60 72 75 85 60 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1280 x 720 70 75 60 70 60 With this option, you can adjust the source coming from your PC in VGA mode (PC1) or DVI (PC2). In DVI, only the horizontal and vertical positions can be adjusted. Horizontal position: press to move it to the right. to move the picture to the left and AUDIO VGA V G A PC1 IN P C 1 recommended for the connection of a PC fitted with a "VGA" socket. A 3. 5 mm audio jack socket allows you to connect sound. Vertical position: Press bottom. or to move the picture to the top or Frequency: This allows you to adjust the frequency to that of your computer's graphics card. When a flashing vertical bar appears, use this function to adjust the frequency. 7. 2. Source configuration IMAGE CODE PROTECTION CONFIG SOURCES MANAGER AUTO CODE PC DATA CHANNEL MAN. EPG Phase: This allows finer synchronization with your computer's graphics card. Use this tuning when an unstable or flashing picture occurs. AUDIO OPTIONS INSTALL. Press the MENU key then select "INSTALL" using the button and validate using OK. If your code is not 0000, this screen is protected and you must enter your code. Select "SOURCES", then "CONFIG" and accept with OK. This option allows you to select the sources used but only displays them when you select sources in daily use. Automatic mode: This allows you to adjust everything automatically or not. Resolutions accepted (DVI-D and VGA entries): To ensure that the projection display is operating correctly with your computer make sure that you configure the display mode of your graphics card to a resolution lower than 1024 x 768. NB: Optimum stability is achieved with a frequency of 60 Hz (consult the documentation for your PC to configure it). / ). Choose the connector to be configured ( For each connector, you can: INPUT SOURCE N° NAME N. R. 8. · Validate connected equipment Press the red key several times until "YES" (or "NO" for an unused connector) is displayed. Select "C+" if you have connected your C+ decoder to SCART 2. In this instance, enter the C+ programme number at once. Day-to-day use 8. 1. Picture adjustment PERSONAL PICTURE TUNING IMAGE USER SCART 1 SCART 2 SCART 3 AV 4 AV 5 AV 6 PC 1 PC 2 YES YES YES YES YES YES YES YES ------ ------------------------------------NAME N. R. 0 0 0 0 0 0 AUDIO STANDARD OPTIONS CINEMA STUDIO INSTALL. SPORT · Choosing a pre-programmed name Press the green button several times (DVD, DVDR, C+, DEC, MAG, GAMES). OK CONTRAST BRIGHTNESS COLOR 50 50 50 You can set and save your own parameters using the "USER" mode. CONTRAST, BRIGHTNESS, COLOUR, SHARPNESS, TINT be adjusted according to your preferences using the buttons and . [. . . ] Diagnosing Trouble Shooting Symptoms: When first using your SAGEM AXIUMTM Home Check that the mains cable to SAGEM AXIUMTM Home Cinema Screen is Cinema Screen, the red on/off indicator light is not connected to the appliance and the wall socket. Also check that the switch on the left side of the appliance is pressed in. 14. Changing the lamp unit Recommended checks: Only replace the old lamp unit with authorised model RL1280A, reference number SAGEM 251691414 The old lamp unit must be recycled (contact your recycling agency to obtain the address of the nearest depot). 1. You must only change the lamp unit, when the appliance is switched off and mains cable disconnected from the wall socket. The appliance does not light up when the Check that the mains cable to SAGEM AXIUMTM Home Cinema Screen is on/standby button is pressed on the right side connected to the apparatus and the mains socket. [. . . ]