User manual PHILIPS SWW1810

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PHILIPS SWW1810. We hope that this PHILIPS SWW1810 user guide will be useful to you.


PHILIPS SWW1810 : Download the complete user guide (2137 Ko)

You may also download the following manuals related to this product:

   PHILIPS SWW1810 (2185 ko)
   PHILIPS SWW1810 (2148 ko)
   PHILIPS SWW1810 QUICK START GUIDE (1495 ko)
   PHILIPS SWW1810 QUICK START GUIDE (1495 ko)
   PHILIPS SWW1810 QUICK START GUIDE (1495 ko)

Manual abstract: user guide PHILIPS SWW1810

Detailed instructions for use are in the User's Guide.

[. . . ] liquid filled objects, lighted candles). Warning · Use only the provided power adapter. EN 5 English 2 Your Wireless HD AV Connect Congratulations on your purchase and welcome to Philips!To fully benefit from the support that Philips offers, register your product at www. philips. HDMI cable IR blaster extender cable What is in the box Note · Make sure you have all these items in the box. Contact your dealer for any missing or damaged items. Power adapter for the transmitter and receiver x2 IR sensor extender cable Transmitter Anchors x 2 Screws x 2 Quick Installation Guide Receiver Adhesive tape x 2 Quick start guide User manual Remote control 6 EN The transmitter Front view Top view 1 1 2 3 Source LEDs It displays the current source input. [. . . ] HDMI On mode with unrecognized CH1 video format HDMI On mode but without input CH1 from the source device HDMI On mode with recognized video CH1 1080P format 1 2 Go to the source menu under the settings menu of your HDTV. Select the HDMI input to which the receiver is connected. HDM I EN 11 Activate the wireless link Switch on the transmitter and receiver In standby mode, a red power LED displays on the transmitter and receiver. You can then turn on the transmitter and receiver in the following ways: Select the source on the transmitter Press the source buttons on the remote control, transmitter or receiver until you see the available video from your device. Tip · For information on the LED indicator status, see the section on `LED indicator status of the transmitter'. LED indicator status of the transmitter and receiver Power LED Solid red Flashing blue Flashing blue Solid blue Solid blue Solid blue · Press on the transmitter and receiver. Source Mode and status LED Off Standby mode: it is a power-saving mode Flashing Start up in progress: It takes blue 15-20 seconds. Flashing Searching available channels: It occurs when the link cannot establish over 80 seconds after initialization. Flashing On mode but without quickly input from the source device Flashing On mode with slowly unrecognized video format Solid On mode with recognized blue video format · Press on the remote control. » Both the transmitter and receiver are turned on. Note · If the link is not established after 80 seconds, move the transmitter, receiver and HDTV closer to each other. If more than one set of Philips Wireless HD AV Connect is placed in the same room, make sure that the minimum distance among each one is 6 feet 6 inches (2 meters). If using a computer, make sure the video format is supported before the video is displayed, see the chapter on `Technical data' for information. If using a computer, and the picture on your TV is not full screen, see the chapter on `Frequently asked questions' for information. Establish the link between the transmitter and receiver A flashing blue power LED displays until the signal link between the two units are established. Normally, it takes around 15-20 seconds for the link to establish successfully. · · · 12 EN 6 Mount your receiver You can either mount the receiver on the wall or on the back of the HDTV. 5 Mount your receiver on the wall 1 2 3 4 Select a spot near the HDTV. Make sure that the distance between the two holes is 1 25/32" (45 mm) and the diameter of the hole is 3/16" (5 mm). Put the two screws into the anchors and leave 1/8" (3 mm) to mount the receiver on. EN 13 English Hook the key holes at the back of the receiver on the screws. Mount your receiver on the back of the HDTV 1 2 Remove the white protective film from one of the supplied adhesive tapes. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. · Operations in the 5. 15-5. 25GHz / 5. 7255. 825GHz band are restricted to indoor usage only. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: · This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. [. . . ] 3) Make sure that the video solution your source device is supported (See the chapter `Technical data'). · Solid blue power LED + quick and flashing source LED: 1) Make sure that the proper cables are connected among the transmitter, receiver and HDTV. 2) Make sure that the source devices connected to the transmitter are powered on. 1 2 3 4 5 6 There is no video displayed on · my TV screen. · · 18 EN · Tip · For information, see the chapter on `Technical data'. I cannot hear any sound or the · sound is poor, what do I do? [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PHILIPS SWW1810




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PHILIPS SWW1810 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.