User manual ORANGE D10-30NG QUICK GUIDE

[. . . ] This symbol indicates important instructions accompanying the product. WARNING :  To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION :  TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. • This apparatus shall always be connected to a AC outlet with a protective grounding connection. • To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. [. . . ] 5. In the "Service Set ID (SSID)" field, select the AP device (router or modem) your Wi-Fi device is connected to. 6. Type the AP device's password into the "WPA Passphrase" filed. 8. When the connection between the Wireless Audio with Dock and AP you selected is completed, the indicator on the Wireless Audio with Dock changes to white. • The Wireless Audio with Dock connection is complete. 7 6 5 6  The picture above is the screen which will appear on the display after completing the network connection successfully, so you can run AirPlay or DLNA normally. 18 To connect the Wireless Audio with Dock using a WPS PIN 1. Press the button on the top panel of the Wireless Audio with Dock repeatedly until the icon appears in the display. • Each time you press the button, the selection changes as follows : ; ; ; ; ; ; AUX (LED Off) The indicator changes from white to red and blinks. 2. Press and hold the WPS/RESET button on the back panel with a pen tip or similar item for more than 5 seconds. Wait until the indicator blinks in white twice more, and then release the WPS/RESET button. • The icon blinks in red, and then stops blinking and glows in red when the unit accesses the Network Setting mode. 3. To connect the Wireless Audio with Dock to the network, search for "Samsung W_Audio E750 XXXXXXX" in the Wi-Fi Setting list of your WI-Fi device, and then select it. ex) Samsung Galaxy Device or EnG ● connections 4. Open the web browser of the Wi-Fi device, and then type "http://192. 168. 1. 1" into the address bar of the Internet browser. Note or write down the number, and then turn the Wireless Audio with Dock unit off and then on. -- If several Bluetooth devices are simultaneously paired to the Wireless Audio with Dock. -- If the Bluetooth device is turned off, not in place, or malfunctions -- Note that such devices as microwave ovens, wireless LAN adaptors, fluorescent lights, and gas stoves use the same frequency range as the Bluetooth device, which can cause electric interference. 20 cOnnecting tO BLUetOOtH DeVices This section explains how to connect the Wireless Audio with Dock to Bluetooth compatible TVs and other Bluetooth devices. EnG to connect the wireless Audio with Dock to a Bluetooth compatible 2012 Samsung tv (SoundShare) DOCK ● connEctions connect <to pair to your tv> To produce TV sound on your Wireless Audio with Dock via Bluetooth connection, you need to pair your system to the Bluetooth compliant TV first. Once the pairing is established, the pairing information is recorded and kept and no further Bluetooth connection message will appear from the next time. Keep the Wireless Audio with Dock and the TV close together before pairing. • Set "Add New Device" menu to "On" in the TV. (For more information, refer to the user's guide of TV) Menu ; System ; Device Manager ; SoundShare Settings ; Add New Device. When you change the mode of Wireless Audio with Dock to , a message asking whether to proceed with Bluetooth pairing appears. Select <yes> on the TV screen, then the pairing with the Wireless Audio with Dock will be completed. • The Wireless Audio with Dock Bluetooth pairing is complete. <to cancel pairing to your tv> If you want to pair your Wireless Audio with Dock to a TV other than the connected TV, you should cancel the existing pairing in the Wireless Audio with Dock. The LED will blink once when you press the wPS/reSet button on the rear panel of the unit for 1 second in . This unit will automatically pair to a TV once you cancel the existing pairing and the new TV is ready for connection. ▪ If the TV cannot be connected, please try to reconnect it after pressing the WPS/RESET button on the rear panel of the set in the Bluetooth mode. ▪ You should update TV software to the latest version to operate TV pairing (SoundShare) function. [. . . ] Click get downloads in the Center of the page below the Downloads header. Once popup window appears, click oK and continue to download and save upgrade file onto your PC. Copy all files in the folder to the USB flash drive’s root directory. • Upgrading allows only one file set for upgrading at a time. PUSH PUSH LAN WPS / RESET AUX IN ONLY FOR SERVICE USB 5V 500mA POWER LAN WPS / RESET AUX IN ONLY FOR SERVICE USB 5V 500mA POWER 10. [. . . ]