User manual NAIM NAIT5

[. . . ] OWNERS MANUAL Integrated Amplifier page 1 1. 0 Equipment Installation 1. 1 cables and connections 2 2. 0 Getting Started 2. 1 2. 2 2. 3 2. 4 2. 5 3 switching on and off running in mains supply siting the equipment if you have a problem 3. 0 Warnings 4. 0 Connection 4 4. 1 mains lead 4. 2 non-rewireable mains plugs 4. 3 fuse carrier 4. 4 plug fuses 5 Nait 5 Integrated Amplifier Narcom 2 Remote Control Specifications, EC Declaration of Conformity to Appropriate Standards 10 12 1. 0 Equipment installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. 1. 1 cables and connections Please do not modify the standard interconnect cables supplied with your Naim equipment. One end of each cable is marked with a band to establish its correct orientation. Naim loudspeaker cable is correct for your system and your dealer will make up leads to suit your equipment installation. [. . . ] Considerable shock hazard exists if the cut-off plug is inserted into a mains outlet. 4. 3 fuse carrier Should the plug fuse carrier be damaged or lost, the correct replacement must be obtained from your dealer or from Naim direct. Do not use the plug until the fuse carrier is replaced. 4. 4 plug fuses Replace only with ASTA or BS 1362 approved fuses. note This equipment has been tested and found to comply with the relevant EMC and Safety Standards, and, where applicable, also complies with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your Naim dealer or an experienced radio/TV technician for help. 4 Nait 5 Integrated Amplifier inputs The Nait 5 has 6 inputs - CD, Tuner, Tape, A/V, AUX1 and AUX 2. Tape, A/V and AUX 1 all have record output facilities for your cassette deck, VCR etc. Use the right hand socket (when viewed from the rear) for commenting your usual ancillary equipment. The extra (left hand) socket is for use with separate phono stage, such as the Prefix or Stageline. Only one of these sockets may be used at a time, for safety as well as performance. Your amplifier will have a protective cover fitted over the extra socket. If you wish to use this socket it is advisable to refit the protective cover over the unused socket to prevent mistakes. tape facilities and monitor button The tape monitor (mon) button allows you to listen to the output of a 3-head tape machine while recording to check the "off-tape" signal. The source for recording is chosen by the input selector buttons in the normal way. Pressing the monitor button during recording allows the output from a 3-head tape machine connected to either tape, A/V or AUX 1 to be heard. After pressing "mon", select whichever one of these your tape machine is connected to. A second press returns the amp to normal position. mute button Pressing the mute button reduces the output from the loudspeakers to zero. (This will not affect any recordings taking place at the same time). balance adjustment Balance adjustment (left to right) on the Nait 5 is operated electronically within the amplifier. Each of the inputs can be adjusted so that the volume level from all sources can be matched to one another. Some movement of the board and sockets when connecting/disconnecting is normal. 6 nait 5 connected to power supply input signal out A signal out B AUX 2 AUX 1 A/V tape tuner cd + - - + power to left loudspeaker ch1 to right loudspeaker mains input ch2 link plug fitted flatcap 2 power supply signal out A signal out B signal out C signal out D power out A power mains input for CD5, Headline or Stageline (additional interconnects required) Interconnect Cables 4 to 4 pin DIN 5 to5 pin DIN cable direction marker 7 nait 5 connected to power amp NB - do not connect nait 5 to mains in this configuration. input signal out A signal out B AUX 2 AUX 1 A/V tape tuner cd + - - + power amp + - - + input power to left loudspeaker ch1 to right loudspeaker mains input ch2 cable direction marker Interconnect Cables 4 to 4 pin DIN 5 to5 pin DIN 8 nait 5 connected to flatcap 2 power supply & power amp NB - do not connect nait 5 to mains in this configuration. input signal out A signal out B AUX 2 AUX 1 A/V tape tuner cd + - - + link plug fitted flatcap 2 power supply signal out A signal out B signal out C signal out D power out A power mains input power amp + - - + power to left loudspeaker ch1 to right loudspeaker mains input ch2 cable direction marker Interconnect Cables 4 to 4 pin DIN 5 to5 pin DIN 9 n2 System Component Keys Global Keys (Amplifier) Global Keys (CD Player) Global Keys (Tuner) Soft Keys narcom 2 remote handset NARCOM 2 is a multi-functional remote control handset designed to be used with Naim Audio CD players, integrated amplifiers, pre-amplifiers and preset tuners. [. . . ] To access automatic source switching enter program mode as described above. The mon button on the amplifier will illuminate when source switching is automated. To utilise the surround sound processor unity gain function, enter program mode as described above. The mute button on the amplifier will illuminate when unity gain is selected. [. . . ]