User manual MSI MS-91F7 V1.X

[. . . ] MS-91F7 (v1. X) Server Board Preface Copyright Notice The materal n ths document s the ntellectual property of MICRO-STAR INTERNATIONAL. We take every care n the preparaton of ths document, but no guarantee s gven as to the correctness of ts contents. Our products are under contnual mprovement and we reserve the rght to make changes wthout notce. Trademarks All trademarks are the propertes of ther respectve owners. MSI® s regstered trademark of Mcro-Star Int'l Co. , Ltd. Realtek® s regstered trademark of Realtek Semconductor Corporaton. [. . . ] DDR3 240-pin, 1. 5V 48x2=96 pin 72x2=144 pin Memory Population Rules In Multi-Channel mode, make sure that you install memory modules of the same type and density in different channel DIMM slots. CPU0_DIMM_A1 CPU0_DIMM_A0 CPU0_DIMM_B1 CPU0_DIMM_B0 CPU1_DIMM_B0 CPU1_DIMM_B1 CPU1_DIMM_A0 CPU1_DIMM_A1 For CPU0 Population Rules 1 DIMM 2 DIMMs 3 DIMMs 4 DIMMs CPU0_DIMM_A1 (1) CPU0_DIMM_A1 + CPU0_DIMM_B1 (Dual-Channel) (2) CPU0_DIMM_A1 + CPU0_DIMM_A0 (Single-Channel) CPU0_DIMM_A1 + CPU0_DIMM_A0 + CPU0_DIMM_B1 CPU0_DIMM_A1 + CPU0_DIMM_A0 + CPU0_DIMM_B1 + CPU0_DIMM_B0 For CPU1 Population Rules 1 DIMM 2 DIMMs 3 DIMMs 4 DIMMs CPU1_DIMM_A1 (1) CPU1_DIMM_A1 + CPU1_DIMM_B1 (Dual-Channel) (2) CPU1_DIMM_A1 + CPU1_DIMM_A0 (Single-Channel) CPU1_DIMM_A1 + CPU1_DIMM_A0 + CPU1_DIMM_B1 CPU1_DIMM_A1 + CPU1_DIMM_A0 + CPU1_DIMM_B1 + CPU1_DIMM_B0 2-6 MS-91F7 Installing Memory Modules 1. The memory module has only one notch on the center and will only fit in the right orientation. Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot. The plastic clip at each side of the DIMM slot will automatically close when the memory module is properly seated. Manually check if the memory module has been locked in place by the DIMM slot clips at the sides. Important You can barely see the golden finger if the memory module is properly inserted in the DIMM slot. Notch Volt Important · To enable successful system boot-up, always insert the memory modules into the DIMM_A1 first. · If users intend to install two DIMMs, it is highly suggested that these DIMMs are populated in DIMM_A1 and DIMM_B1 for enhanced Dual-Channel memory performance. · In Dual-Channel mode, make sure that memory modules of the same type and density are installed in different channel DIMM slots. 2-7 Hardware Setup power SuppLy System Power Connector: JPWR1 Ths connector allows you to connect a power supply. To connect to the power supply, make sure the plug of the power supply s nserted n the proper orentation and the pins are aligned. Then push down the power supply firmly into the connector. PIN 1 2 3 4 5 6 7 8 9 10 11 12 SIGNAL +3. 3V +3. 3V GND +5V GND +5V GND PWR OK 5VSB +12V +12V +3. 3V PIN 13 14 15 16 17 18 19 20 21 22 23 24 SIGNAL +3. 3V -12V GND PS-ON# GND GND GND +3. 3VSB +5V +5V +5V GND 24 12 13 1 CPU/Memory Power Connector: JPWR2 Ths connector provdes 12V power output to the CPUs & memory. PIN 8 4 5 1 1 2 3 4 5 6 7 8 SIGNAL GND GND GND GND +12V +12V +12V +12V Important Make sure that all power connectors are connected to the power supply to ensure stable operation of the mainboard. 2-8 MS-91F7 rear paneL i/o Mouse Port VGA Port LAN Jack LAN Jack Keyboard Port Serial Port USB Port USB Port Mouse/Keyboard Port The standard PS/2 mouse/keyboard DIN connector s for a PS/2 mouse/keyboard. Serial Port The seral port s a 16550A hgh speed communcatons port that sends/ receves 16 bytes FIFOs. You can attach a seral mouse or other seral devces drectly to the connector. USB Port The USB (Unversal Seral Bus) port s for attachng USB devces such as keyboard, mouse, or other USB-compatble devces. LAN The standard RJ-45 LAN jack s for connecton to the Local Area Network (LAN). You can connect a network cable to t. LED Left Color Yellow LED State Off On (steady state) On (blnkng) Rght Green Off On Orange On Condton LAN lnk s not establshed. 1000 Mbt/sec data rate s selected. Yellow Green/ Orange 2-9 Hardware Setup connector Serial ATA Connector: SATA_0 ~ SATA_5 Ths connector s a hgh-speed Seral ATA nterface port. Each connector can connect to one Seral ATA devce. Important Please do not fold the SATA cable into a 90-degree angle. Otherwise, data loss may occur during transmission. Fan Power Connector: CPUFAN0/1, SYSFAN1/2/3 The fan power connectors support system coolng fan wth +12V. When connectng the wre to the connectors, always note that the red wre s the postve and should be connected to the +12V; the black wre s Ground and should be connected to GND. If the manboard has a System Hardware Montor chpset onboard, you must use a specally desgned fan wth speed sensor to take advantage of the CPU fan control. PIN 1 2 3 4 SIGNAL GND +12V Sensor Control 1 4 Important Please refer to the recommended CPU fans at processor's official website or consult the vendors for proper CPU cooling fan. 2-10 MS-91F7 Serial Port Connector: JCOM2 Ths connector s a 16550A hgh speed communcatons port that sends/receves 16 bytes FIFOs. You can attach a seral devce to t through the optonal seral port bracket. PIN 1 2 3 4 5 6 7 8 9 SIGNAL DCD SIN SOUT DTR GND DSR RTS CTS RI DESCRIPTION Data Carry Detect Seral In or Receve Data Seral Out or Transmt Data Data Termnal Ready Ground Data Set Ready Request To Send Clear To Send Rng Indcate 2 1 10 9 Front USB Connector: JUSB1, JUSB2 Ths connector, complant wth Intel I/O Connectvty Desgn Gude, s deal for connectng hgh-speed USB nterface perpherals such as USB HDD, dgtal cameras, MP3 players, prnters, modems and the lke. PIN 2 1 10 9 1 3 5 7 9 SIGNAL VCC USB0USB0+ GND KEY PIN 2 4 6 8 10 SIGNAL VCC USB1USB1+ GND NC USB 20 Bracket (Optonal) 2-11 Hardware Setup Front Panel Connector: JFP1, JFP2 The front panel connector s provded for electrcal connecton to the front panel swtches and LEDs. 2 1 24 23 2 1 8 7 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 SIGNAL POWER LED+ FRONT PANEL POWER KEY SYS ID LED+ POWER LEDSYS ID LEDHDD ACT LED+ SYS FAULT LED1HDD ACT LEDSYS FAULT LED2POWER SWITCH NIC#1 ACT LED+ POWER SWITCH GND NIC#1 ACT LEDRESET SWITCH SMB SDA RESET SWITCH GND SMB SCL SYS ID SWITCH CHASSIS INTRUSION WIRE TEMP SENSOR NIC#2 ACT LED+ NMI SWITCH NIC# 2 ACT LED- PIN 1 2 3 4 5 6 7 8 SIGNAL GND SPEAKER POWER LED SPEAKER POWER LED SPEAKER KEY SPEAKER 2-12 MS-91F7 Chassis Intrusion Switch Connector: JCI1 Ths connector connects to the chasss ntruson swtch cable. The system wll record ths status and show a warnng message on the screen. To clear the warnng, you must enter the BIOS utlty and clear the record. CINTRU GND IPMB Connector: J_IPMB1 Ths connector s used to connect the IPMB (Intellgent Platform Management Bus) SMBus. PIN 1 1 2 3 SIGNAL SMB_IPMB_5VSB_DAT GND SMB_IPMB_5VSB_CLK 2-13 Hardware Setup JuMper Clear CMOS Jumper: JBAT1 There s a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration. [. . . ] Set to [Dsabled] only f you want to use any USB devce other than the USB mouse. 3-12 MS-91F7 boot Boot Settings Configuration Quick Boot Enablng ths settng wll cause the BIOS power-on self test routne to skp some of ts tests durng bootup for faster system boot. 3-13 BIOS Setup Display Full Screen Logo Ths BIOS feature determnes f the BIOS should hde the normal POST messages wth the motherboard or system manufacturer's full-screen logo. When t s enabled, the BIOS wll dsplay the full-screen logo durng the bootup sequence, hdng normal POST messages. When t s dsabled, the BIOS wll dsplay the normal POST messages, nstead of the full-screen logo. [. . . ]