User manual MSI MS-7597 V1.5

[. . . ] Notce 2 Shelded nterface cables and AC power cord, f any, must be used n order to comply wth the emsson lmts. Operaton s subject to the followng two condtons: 1) ths devce may not cause harmful nterference, and 2) ths devce must accept any nterference receved, ncludng nterference that may cause undesred operaton. To protect the global envronment and as an envronmentalst, MSI must remnd you that. Under the European Unon ("EU") Drectve on Waste Electrcal and Electronc Equpment, Drectve 2002/96/EC, whch takes effect on August 13, 2005, products of "electrcal and electronc equpment" cannot be dscarded as muncpal waste anymore and manufacturers of covered electronc equpment wll be oblgated to take back such products at the end of ther useful lfe. [. . . ] ⷠTo enable successful system boot-up, always nsert the memory modules nto the DIMM1 first. ⷠDue to the chpset resource deployment, the system densty wll only be detected up to 15+GB (not full 16GB) when each DIMM s nstalled wth a 4GB memory module. The memory module has only one notch on the center and wll only fit n the rght orentaton. Then push t n untl the golden finger on the memory module s deeply nserted n the DIMM slot. The plastc clp at each sde of the DIMM slot wll automatcally close when the memory module s properly seated. Manually check f the memory module has been locked n place by the DIMM slot clps at the sdes. You can barely see the golden finger f the memory module s properly nserted n the DIMM slot. To connect the ATX 24-pn power supply, make sure the plug of the power supply s nserted n the proper orentaton and the pns are algned. If you'd lke to use the 20-pn ATX power supply, please plug your power supply along wth pn 1 & pn 13. Make sure that all the connectors are connected to proper ATX power supples to ensure stable operaton of the manboard. You can attach a seral mouse or other seral devces drectly to the connector. The IRQ, acronym of nterrupt request lne and pronounced I-R-Q, are hardware lnes over whch devces can send nterrupt sgnals to the mcroprocessor. Enablng game-domnatng power, ATI CrossFreXTM technology enables two or more dscrete graphcs processors to work together to mprove system performance. ATI CrossFreXTM technology allows you to expand your system's graphcs capabltes. It allows you the ablty to scale your system's graphcs horsepower as you need t, supportng two or more ATI RadeonTM HD graphcs cards, makng ths the most scalable gamng platform ever. The manboard can auto detect the CrossFreXTM mode by software, therefore you don't have to enable the CrossFreXTM n BIOS by yourself. Wth two cards nstalled, an CrossFreXTM Vdeo Lnk cable s requred to connect the golden fingers on the top of these two graphcs cards (refer to the pcture below). Please note that although you have nstalled two or more graphcs cards, only the vdeo outputs on the graphcs card nstalled n first PCIE x16 wll work. The appearance of your motherboard may vary dependng on the model you purchase. ⷠIf you ntend to nstall TWO graphcs cards for CrossFreXTM mode, make sure that: a. ⷠMake sure that you connect an adequate power supply to the power connector on the graphcs card to ensure stable operaton of the graphcs card. ⷠOnly Wndows®XP wth Servce Pack 2 (SP2)& Wndows®XP Professonal x64 Edton & Wndows®Vsta & Wndows® 7 support the CrossFreXTM functon. [. . . ] Overclockng Profile Use ths menu to save/ load your settngs to/ from CMOS for BIOS. Load Fal-Safe Defaults Use ths menu to load the default values set by the BIOS vendor for stable system performance. Load Optmzed Defaults Use ths menu to load the default values set by the manboard manufacturer specfically for optmal performance of the manboard. When enter the BIOS Setup utlty, follow the processes below for general use. [. . . ]