User manual MSI MS-7522 V5.0 V5.0

[. . . ] X58A-GD45 series MS-7522 (v5. x) Mainboard G52-75221XE Preface Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. MSI® is registered trademark of Micro-Star Int'l Co. , Ltd. Sound Blaster® is registered trademark of Creative Technology Ltd. [. . . ] AHCI Configuration When the "RAID Mode" sets to [AHCI], this field is available. Press <Enter> to enter the sub-menu and the following screen appears: AHCI Port 1/2/3/4/5/6 Press <Enter> to enter the sub-menu. I/O Devices Press <Enter> to enter the sub-menu and the following screen appears: COM Port 1 Select an address and corresponding interrupt for the serial port. 3-11 BIOS Setup Power Management Setup Important S3-related functions described in this section are available only when the BIOS supports S3 sleep mode. ACPI Function This item is to activate the ACPI (Advanced Configuration and Power Management Interface) Function. ACPI Standby State This item specifies the power saving modes for ACPI function. Power LED This item configures how the system uses power LED to indicate the sleep state. EuP 2013 This item is designed for Energy Using Products Lot 6 2013 (EuP) aka Energy Related Products (ErP). Note: When "Enabled" EuP 2013 setting, system don't support RTC wake up event function. S4/S5 PowerOn Wait (Sec) This item allows you to select a waiting period when system wake-up from power state S4/S5. 3-12 MS-7522 Restore On AC Power Loss This item specifies whether your system will reboot after a power failure or interrupt occurs. Settings are: [Off] Always leaves the computer in the power off state. [Last State] Restore the system to the status before power failure or interrupt occurred. Wake Up Event Setup Press <Enter> and the following sub-menu appears. Chapter 3 Wake up Event By Setting to [BIOS] activates the following fields, and use the following fields to set the wake up events. Resume From S3 By USB Device The item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state. Resume From S3 By PS/2 Keyboard / Mouse These items determine whether the system will be awakened from what power saving modes when input signal of the PS/2 keyboard/ mouse is detected. Resume By PCI-E Device When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PCIE device. Resume By RTC Alarm The field is used to enable or disable the feature of booting up the system on a scheduled time/date. Date/ HH:MM:SS If Resume By RTC Alarm is set to [Enabled], the system will automatically resume (boot up) on a specific date/hour/minute/second specified in these fields (using the <+> and <-> to select the date & time settings). Available settings for each item are: [Date] 01 ~ 31, Every Day [HH:MM:SS] 00 ~ 23 : 00 ~ 59 : 00 ~ 59 3-13 BIOS Setup H/W Monitor Chassis Intrusion The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. The setting of the field will automatically return to [Enabled] later. CPU Smart FAN Target The mainboard provides the Smart Fan function which can control the CPU fan speed automatically depending on the current temperature to keep it with in a specific range. If the current CPU fan temperature reaches to the target value, the smart fan function will be activated. It provides several sections to speed up for cooling down automatically. [. . . ] Press Y to confirm the request when prompted Do you want to delete this virtual disk?. Press Y to confirm the request when prompted Do you want to delete MBR from this virtual disk?. Marvell BIOS Setup (c) xxxx Marvell Technology Group Ltd. Topology HBA 0: Marvell 0 Virtual Disks VD 0: MRAID1 PD 0: ST3750330MS [Delete] PD 8: ST3750330MS Free Physical Disks Information ID Namd Status Stripe Size RAID Mode Size BGA Status Number of PDs Members : : : : : : : : : 0 MRAID1 Functional 64K RAID1 953344MB N/A 2 08 Help Delect the selected virtual disk. ENTER: Operation F10: Exit/ Save ESC: Return C-6 MS-7522 Rebuilding Virtual Disk This topic describes the procedure to manually rebuild a degraded virtual disk by using the Marvell BIOS setup utility. [. . . ]