User manual MSI MD 5000

[. . . ] Medion® shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. 1-1 MD5000 M-ATX Mainboard Mainboard Specifications CPU Supports Socket 478 for P4/Celeron processors (Willimate and Northwood core) with 400/533 MHz Core Frequency from 1. 3 GHz to 2. 8 GHz and up Chipset SiS® 648 chipset - Supports Intel Pentium 4 processors with data transfer rate up to 533 MHz - Supports 64-bit high performance DDR333+/DDR333/DDR266 memory controller - Supports AGP 8X/4X interface - Supports bi-directional 16-bit data bus with 1 GHz bandwidth MuTIOL SiS® 963 chipset - Supports Dual-IDE ATA 66/100/133 - Integrated audio controller with AC97 interface - Low pin count interface for SIO - Advanced power management and PC2001 compliance Main Memory Supports two 184-pin DDR DIMMs Supports up to 2GB PC2700/2100/1600 DDR SDRAMs Supports 2. 5v DDR SDRAM Slots One AGP (Accelerated Graphics Port) 4x/8x slot. On-BoardIDE Dual-IDE controller integrated in SiS 963 chipset Supports PIO, Bus Master and Ultra DMA133/100/66/33 operation modes Can connect up to four IDE devices. On-Board Peripherals On-Board Peripherals include: - 1 floppy port supports 2 FDDs with 360K, 720K, 1. 2M, 1. 44M and 2. 88Mbytes - 1 serial port 1-2 Getting Started - 1 parallel port - Audio * 3 in vertical for 6 channels Line-out, 2 in vertical for MIC & Linein - 1 standard 1394 connector - 1 mini 1394 connector - 5 USB ports (3 front + 2 rear) - 1 RJ-45 Lan Jack (optional) - PS2 KB/Mouse OnboardIEEE1394 Integrated in SiS 963 SB AGREE FW803 Audio S/W RealTek ALC650 6-channel audio codec with SPDIF in/out LAN Realtek RTL8201BL BIOS The mainboard BIOS provides "Plug & Play" BIOS which detects the peripheral devices and expansion cards of the board automatically. [. . . ] You can install DDR200/266/333 modules on the DDR DIMM slots (DIMM 1~2). DDR DIMM Slots (DDR 1~2) 2-7 MD-5000 M-ATX Mainboard DIMM Module Combination Install at least one DIMM module on the slots. You can install either single- or double-sided modules in any order to meet your own needs. Memory modules can be installed in any combination as follows: Slot DIMM 1 (Bank 0 & 1) DIMM 2 (Bank 2 & 3) Memory Module S/D S/D Total Memory 64MB~1GB 64MB~1GB 64MB~2GB Maximum System Memory Supported S: Single Side D: Double Side Installing DDR Modules 1. Then push it in until the golden finger on the memory module is deeply inserted in the socket. The plastic clip at each side of the DIMM slot will automatically close. Volt Notch MSI Reminds You. . . You can barely see the golden finger if the module is properly inserted in the socket. 2-8 Hardware Setup Power Supply The mainboard supports ATX power supply for the power system. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that no damage will be caused. ATX 20-Pin Power Connector: CONN1 This connector allows you to connect to an ATX power supply. To connect to the ATX power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector. ATX 12V Power Connector: JPW1 This 12V power connector is used to provide power to the CPU. 3 1 4 2 11 1 JPW1 20 10 CONN1 CONN1 Pin Definition PIN 1 2 3 4 5 6 7 8 9 10 SIGNAL 3. 3V 3. 3V GND 5V GND 5V GND PW_OK 5V_SB 12V PIN 11 12 13 14 15 16 17 18 19 20 SIGNAL 3. 3V -12V GND PS_ON GND GND GND -5V 5V 5V JPW1 Pin Definition PIN 1 2 3 4 SIGNAL GND GND 12V 12V 2-9 MD-5000 M-ATX Mainboard Back Panel The back panel provides the following connectors: Mouse Parallel LAN (Optional) 6 Channel L-out MIC Keyboard COM A SPDIF- SPDIF- USB in out IEEE1394 Ports L-in Mouse Connector The mainboard provides a standard PS/2® mouse mini DIN connector for attaching a PS/2® mouse. The connector location and pin assignments are as follows: Pin Definition 6 4 PIN 5 3 1 2 3 4 5 6 SIGNAL Mouse DATA NC GND VCC Mouse Clock NC DESCRIPTION Mouse DATA No connection Ground +5V Mouse clock No connection 2 1 PS/2 Mouse (6-pin Female) 2-10 Hardware Setup Keyboard Connector The mainboard provides a standard PS/2® keyboard mini DIN connector for attaching a PS/2® keyboard. You can plug a PS/2® keyboard directly into this connector. Pin Definition 6 4 1 5 3 PIN 1 2 3 4 5 6 SIGNAL Keyboard DATA NC GND VCC Keyboard Clock NC DESCRIPTION Keyboard DATA No connection Ground +5V Keyboard clock No connection 2 PS/2 Keyboard (6-pin Female) USB Connectors The mainboard provides an OHCI (Open Host Controller Interface) Universal Serial Bus root for attaching USB devices such as keyboard, mouse or other USB-compatible devices. You can plug the USB device directly into the connector. USB Port Description PIN 1 2 3 4 1 2 3 4 5 6 7 8 SIGNAL VCC -Data 0 +Data0 GND VCC -Data 1 +Data 1 GND DESCRIPTION +5V Negative Data Channel 0 Positive Data Channel 0 Ground +5V Negative Data Channel 1 Positive Data Channel 1 Ground 5 6 7 8 USB Ports 2-11 MD-5000 M-ATX Mainboard Parallel Port Connector: LPT1 The mainboard provides a 25-pin female centronic connector as LPT. A parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode. 13 1 25 14 Pin Definition PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 SIGNAL STROBE DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 ACK# BUSY PE SELECT AUTO FEED# ERR# INIT# SLIN# GND GND GND GND GND GND GND GND DESCRIPTION Strobe Data0 Data1 Data2 Data3 Data4 Data5 Data6 Data7 Acknowledge Busy Paper End Select Automatic Feed Error Initialize Printer Select In Ground Ground Ground Ground Ground Ground Ground Ground 2-12 Hardware Setup RJ-45 LAN Jack (Optional) The mainboard provides a RJ-45 connector that allows your computer to be connected to a network environment. LAN Jack (RJ-45) Pin 1 2 3 4 5 6 7 8 Signal TDP TDN RDP NC NC RDN NC NC Description Transmit differential pair Transmit differential pair Receive differential pair Not used Not used Receive differential pair Not used Not used Audio Port Connectors Line Out is a connector for Speakers or Headphones. [. . . ] The mainboard supports 4x/8x 1. 5V AGP card. PCI (Peripheral Component Interconnect) Slots The PCI slots allow you to insert the expansion cards to meet your needs. When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to make any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. [. . . ]