User manual MSI G52-75721X3 V1.0

[. . . ] P45C/P43C Neo Series MS-7572 (V1. X) Mainboard G52-75721X3 i Copyright Notice T he material in this doc ument is the intellec tual property of M ICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trademarks of NVIDIA Corporation in the United States and/or other countries. [. . . ] Fan cooler set with 3 or 4 pins power connector are both available for CPUFAN1. Chassis Intrusion Connector: JCI1 This connector connects to the chassis intrusion switch cable. If the chassis is opened, the chassis intrusion mechanism will be activated. The system will record this status and show a warning message on the screen. To clear the warning, you must enter the BIOS utility and clear the record. GND CINTRU 2 1 JCI1 En-16 IEEE1394 Connector: J1394_1(Optional) English This connector allows you to connect the IEEE1394 device via an optional IEEE1394 bracket. Pin Definition PIN 2 1 10 9 1 3 5 7 9 SIGNAL TPA+ Ground TPB+ Cable power Key (no pin) PIN 2 4 6 8 10 SIGNAL TPAGround TPBCable power Ground J1394_1 IEEE1394 Bracket (Optional) connect the GREEN connector to J1394_1 S/PDIF-Out Connector: JSP1 This connector is used to connect S/PDIF (Sony & Philips Digital Interconnect Format) interface for digital audio transmission. JSP1 VCC SPDIF GND S/PDIF Bracket (Optional) En-17 M S-7572 M ainboard TPM Module Connector: JTPM1 This connector connects to a TPM (Trusted Platform Module) module (optional). Please refer to the TPM security platform manual for more details and usages. 2 1 14 13 Pin 1 3 5 7 9 11 13 Signal LCLK LRST# LAD0 LAD1 LAD2 LAD3 LFRAME# Description LPC clock LPC reset LPC address & data pin0 LPC address & data pin1 LPC address & data pin2 LPC address & data pin3 LPC Frame Pin 2 4 6 8 10 12 14 Signal 3V_STB VCC3 SIRQ VCC5 KEY GND GND Description 3V standby power 3. 3V power Serial IRQ 5V power No pin Ground Ground Front Panel Audio Connector: JAUD1 This connector allows you to connect the front panel audio and is compliant with Intel® Front Panel I/O Connectivity Design Guide. 9 10 1 2 JAUD1 HD Audio Pin Definition PIN 1 2 3 4 SIGNAL MIC_L GND MIC_R PRESENCE# DESCRIPTION Microphone - Left channel Ground Microphone - Right channel Active low signal-signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected 5 6 7 8 9 10 LINE out_R MIC_JD Front_JD NC LINE out_L LINEout_JD Analog Port - Right channel Jack detection return from front panel microphone JACK1 Jack detection sense line from the High Definition Audio CODEC jack detection resistor network No control Analog Port - Left channel Jack detection return from front panel JACK2 En-18 This connector is provided for external audio input. JCD1 R GND L Front Panel Connectors: JFP1, JFP2 These connectors are for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide. JFP1 Pin Definition Power Power LED Switch +PIN 1 2 10 9 +- -+ HDD Reset LED Switch 3 4 5 6 7 8 9 SIGNAL HD_LED + FP PWR/SLP HD_LED FP PWR/SLP RST_SW PWR_SW + RST_SW + PWR_SW RSVD_DNU DESCRIPTION Hard disk LED pull-up MSG LED pull-up Hard disk active LED MSG LED pull-up Reset Switch low reference pull-down to GND Power Switch high reference pull-up Reset Switch high reference pull-up Power Switch low reference pull-down to GND Reserved. Do not use. JFP1 2 1 JFP2 Pin Definition PIN Speaker + +8 7 Power LED 1 2 3 4 5 6 7 8 SIGNAL GND SPKSLED BUZ+ PLED BUZNC SPK+ DESCRIPTION Ground SpeakerSuspend LED Buzzer+ Power LED BuzzerNo connection Speaker+ JFP2 2 1 En-19 English CD-In Connector: JCD1 M S-7572 M ainboard Front USB Connector: JUSB1 ~ 3 These connectors, compliant with Intel® I/O Connectivity Design Guide, is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras, M P3 players, printers, modems and the like. Pin Definition 10 9 PIN 1 3 5 21 7 9 SIGNAL VCC USB0USB0+ GND Key (no pin) PIN 2 4 6 8 10 SIGNAL VCC USB1USB1+ GND USBOC JUSB1~3 USB 2. 0 Bracket (Optional) connect the YELLOW connector to JUSB1/2/3 Important Note that the pins of VCC and GND must be connected correctly to avoid possible damage. En-20 Jumper The motherboard provides the following jumper for you to set the computer's function. This section will explain how to change your motherboard's function through the use of jumper. English Clear CMOS Jumper: JBAT1 There is a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration. W ith the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, set the jumper to clear data. 3 3 1 1 JBAT1 1 Keep Data Clear Data Important You can clear CMOS by shorting 2-3 pin while the system is off. Avoid clearing the CMOS while the system is on; it will damage the mainboard. En-21 M S-7572 M ainboard Switch Hardware Overclock FSB Switch: OC_SW1 You can overclock the FSB to increase the processor frequency by changing the switch OC_SW 1. Follow the instructions below to set the FSB. ON 123 ON 123 ON 123 ON 123 ON 123 Default 200->266 MHz 200->333 MHz 266->333 MHz 200->400 MHz 266->400 MHz 333->400 MHz Important 1. HW overclocking may cause instability or crash during boot, then please re-set the switch to default. BIOS overclocking may also cause crash during boot and then please reboot the system 3 times to restore default BIOS settings. For more details, please refer to the BIOS chapter. En-22 Slots PCI (Peripheral Component Interconnect) Express Slot The PCI Express slot supports the PCI Express interface expansion card. The PCI Express x1 supports up to 250 MB/s transfer rate. English PCI Express x16 Slots support up to PCI Express 2. 0 x16 speed (PCI_E2) White PCI Express x1 Slot supports PCI Express x1 speed (PCI_E1 & PCI_E3) Important When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. En-23 M S-7572 M ainboard PCI (Peripheral Component Interconnect) Slot The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that comply with PCI specifications. 32-bit PCI Slot Important When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. PCI Interrupt Request Routing The IRQ, acronym of interrupt request line and pronounced I-R-Q, are hardware lines over which devices can send interrupt signals to the microprocessor. The PCI IRQ pins are typically connected to the PCI bus pins as follows: Order 1 PCI Slot 1 PCI Slot 2 PCI Slot 3 INT F# INT G# INT A# Order 2 INT G# INT H# INT B# Order 3 INT H# INT E# INT C# Order 4 INT E# INT F# INT D# En-24 LED Status Indicators English CPU Power Phase LEDs ON 123 CPU Power Phase LEDs These LEDs indicate the current CPU power phase mode. Follow the instructions below to read. 3 of the LEDs will light when CPU is in 3 phase power mode. [. . . ] 1 Tc-13 MS-7 5 7 2 FDD1 360KB720KB1. 2MB1. 44MB 2. 88MB FDD1 IDE IDE1 I D E I D E IDE1 IDE / IDE Tc-14 Serial ATA SATA 1~6 SATA SA TA1 -2 SA TA3 -4 SATA6 SATA5 Serial ATA 90 Tc-15 MS-7 5 7 2 CPUFAN1, SYSFAN1/ 2 + 1 2 V +1 2 V ; G ND C P U CONTROL SENSOR +1 2V GND GND +1 2V SENSOR GND +1 2V NC CPUFAN1 SYSFAN1 SYSFAN2 1. CPUFAN1 3 4 / J C I 1 B I O S GND CINTRU 2 1 JCI1 Tc-16 IEEE 1394 : J1394_1() IEEE1394 IEEE1394 1 2 1 10 9 3 5 7 9 TPA+ Ground TPB+ Cable power Key (no pin) 2 4 6 8 10 TPAGround TPBCable power Ground J1394_1 IEEE1394 () J1 39 4_ 1 S/PDIF-Out JSP1 S/PDIF (Sony & Philip Digital Interconnect Format) JSP1 VCC SPDIF GND S/PDIF () Tc-17 MS-7 5 7 2 TPM JTPM1 T PM (Tr ust ed Pl a tf or m M odu l e ) T P M 2 1 14 13 JTPM1 1 3 5 7 9 11 13 LCLK LRST# LAD0 LAD1 LAD2 LAD3 2 4 6 8 10 12 14 3V_STB VCC3 SIRQ VCC5 KEY GND GND LPC clock LPC reset LPC address & data pin0 LPC address & data pin1 LPC address & data pin2 LPC address & data pin3 3V standby power 3. 3V power Serial IRQ 5V power No pin Ground Ground LFRAME# LPC Frame JA U D1 Intel ® I/O 9 10 1 2 JAUD1 HD 1 2 3 4 5 6 7 8 9 10 MIC_L GND MIC_R NC LINE out_R MIC_JD Front_JD NC LINE out_L LINEout_JD Microphone - Left channel Ground Microphone - Right channel Analog Port - Right channel Jack detection return from front panel microphone JACK1 Jack detection sense line from the High Definition Audio CODEC jack detection resistor network No control Analog Port - Left channel Jack detection return from front panel JACK2 Tc-18 CD-In JCD1 R GND L JCD1 LED JFP 1 Intel ® I/O JFP1 Power Power LED Switch + 1 2 3 4 5 6 7 8 9 HD_LED + FP PWR/SLP HD_LED FP PWR/SLP RST_SW PWR_SW + RST_SW + PWR_SW RSVD_DNU JFP1 2 1 10 9 +- -+ HDD Reset LED Switch Hard disk LED pull-up MSG LED pull-up Hard disk active LED MSG LED pull-up Reset Switch low reference pull-down to GND Power Switch high reference pull-up Reset Switch high reference pull-up Power Switch low reference pull-down to GND Reserved. Do not use. JFP2 Speaker + +8 7 Power LED 1 2 3 4 5 6 7 8 GND SPKSLED BUZ+ PLED BUZNC SPK+ Ground SpeakerSuspend LED Buzzer+ Power LED BuzzerNo connection Speaker+ JFP2 2 1 Tc-19 JFP1, JFP2 MS-7 5 7 2 USB JUSB1~3 Intel ® I/O USB : USB MP 3 10 9 1 3 5 21 7 9 VCC USB0USB0+ GND Key (no pin) 2 4 6 8 10 VCC USB1USB1+ GND USBOC JUSB1~3 USB 2. 0 () JU SB1/2/3 VCC GND Tc-20 CMOS JBAT1 CMOS RA MCM OS RA M 3 3 1 1 JBAT1 1 2-3 CMOS 1-2 CMOS Tc-21 MS-7 5 7 2 FSB OC_SW1 F S B F S B ON 123 ON 123 ON 123 ON 123 ON 123 200->266 MHz 200->333 MHz 266->333 MHz 200->400 MHz 266->400 MHz 333->400 MHz 1. BIOS BIOS BIOS BIOS Tc-22 PCI Express PCI Express PCI Express PCI Express 2. 0 x16 8. 0 GB PCI Express x1 250 MB PCI Express x16 PCI Express 2. 0 x16 (PCI_E2) PCI Express x1 PCI Express x1 (PCI_E1 & PCI_E3) BIOS Tc-23 MS-7 5 7 2 PCI (Peripheral Component Interconnect) SCSI USB PCI 32-bit PCI BIOS PCI IRQ (Interrupt request) PCI IRQ PC I Order 1 PCI Slot 1 PCI Slot 2 PCI Slot 3 INT F# INT G# INT A# Order 2 INT G# INT H# INT B# Order 3 INT H# INT E# INT C# Order 4 INT E# INT F# INT D# Tc-24 LED CPU Power Phase LEDs ON 123 CPU LED L ED C P U C PU L E D C PU L E D C PU L E D Tc-25 MS-7 5 7 2 BIOS B I O S B I O S : * B I O S * B I O S 1 . [. . . ]