User manual MSI G52-75631X3 V1.0

[. . . ] G41M Series MS-7563 (V1. X) Mainboard G52-75631X3 i Copyright Notice T he material in this doc ument is the intellec tual property of M ICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trademarks of NVIDIA Corporation in the United States and/or other countries. [. . . ] If the chassis is opened, the chassis intrusion mechanism will be activated. The system will record this status and show a warning message on the screen. To clear the warning, you must enter the BIOS utility and clear the record. CINTRU 12 GND JCI1 En-16 IEEE1394 Connector: J1394_1 (optional) English This connector allows you to connect the IEEE1394 device via an optional IEEE1394 bracket. Pin Definition PIN 2 1 10 9 1 3 5 7 9 SIGNAL TPA+ Ground TPB+ Cable power Key (no pin) PIN 2 4 6 8 10 SIGNAL TPAGround TPBCable power Ground J1394_1 (optional) IEEE1394 Bracket (Optional) S/PDIF-Out Connector: JSPD1 This connector is used to connect S/PDIF (Sony & Philips Digital Interconnect Format) interface for digital audio transmission. JSPD1 S/PDIF Bracket (Optional) GND SPDIF VCC En-17 M S-7563 M ainboard Front Panel Connectors: JFP1, JFP2 These connectors are for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide. JFP1 10 Power Switch + Power LED 2 9 + Reset - Switch - HDD + LED JFP2 + Speaker 8 + 2 1 7 Power LED 1 JFP1 Pin Definition PIN 1 2 3 4 5 6 7 8 9 SIGNAL HD_LED + FP PWR/SLP HD_LED FP PWR/SLP RST_SW PWR_SW + RST_SW + PWR_SW RSVD_DNU DESCRIPTION Hard disk LED pull-up MSG LED pull-up Hard disk active LED MSG LED pull-up Reset Switch low reference pull-down to GND Power Switch high reference pull-up Reset Switch high reference pull-up Power Switch low reference pull-down to GND Reserved. Do not use. JFP2 Pin Definition PIN 1 2 3 4 5 6 7 8 SIGNAL GND SPKSLED BUZ+ PLED BUZNC SPK+ DESCRIPTION Ground SpeakerSuspend LED Buzzer+ Power LED BuzzerNo connection Speaker+ CD-In Connector: CD_IN1 This connector is provided for external audio input. CD_IN1 L GND R En-18 Front Panel Audio Connector: JAUD1 English This connector allows you to connect the front panel audio and is compliant with Intel® Front Panel I/O Connectivity Design Guide. 2 1 10 9 JAUD1 HD Audio Pin Definition PIN 1 2 3 4 SIGNAL MIC_L GND MIC_R PRESENCE# DESCRIPTION Microphone - Left channel Ground Microphone - Right channel Active low signal-signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected Analog Port - Right channel Jack detection return from front panel microphone JACK1 Jack detection sense line from the High Definition Audio CODEC jack detection resistor network No control Analog Port - Left channel Jack detection return from front panel JACK2 5 6 7 8 9 10 LINE out_R MIC_JD Front_JD NC LINE out_L LINEout_JD TPM Module connector: JTPM1(optional) This connector connects to a TPM (Trusted Platform Module) module (optional). Please refer to the TPM security platform manual for more details and usages. JTPM 1 14 13 2 1 Pin 1 3 5 7 9 11 13 Signal LCLK LRST# LAD0 LAD1 LAD2 LAD3 LFRAME# Description LPC clock LPC reset LPC address & data pin0 LPC address & data pin1 LPC address & data pin2 LPC address & data pin3 LPC Frame Pin 2 4 6 8 10 12 14 Signal 3V dual/3V_STB VCC3 SIRQ VCC5 KEY GND GND Description 3V dual or 3V standby power 3. 3V power Serial IRQ 5V power No pin Ground Ground En-19 M S-7563 M ainboard Front USB Connector: JUSB1 ~ 2 These connectors, compliant with Intel® I/O Connectivity Design Guide, is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras, M P3 players, printers, modems and the like. Pin Definition JUSB1~2 2 1 10 9 PIN 1 3 5 7 9 SIGNAL VCC USB0USB0+ GND Key (no pin) PIN 2 4 6 8 10 SIGNAL VCC USB1USB1+ GND USBOC USB 2. 0 Bracket (Optional) Important Note that the pins of VCC and GND must be connected correctly to avoid possible damage. Serial Port Connector: JCOM 1 This connector is a 16550A high speed communication port that sends/receives 16 bytes FIFOs. You can attach a serial device. Pin Definition JCOM1 9 PIN 1 2 3 4 5 6 7 8 9 SIGNAL DCD SIN SOUT DTR GND DSR RTS CTS RI DESCRIPTION Data Carry Detect Serial In or Receive Data Serial Out or Transmit Data Data Terminal Ready Ground Data Set Ready Request T Send o Clear To Send Ring Indicate 2 1 En-20 Parallel Port Header: JLPT1 This connector is used to connect an optional parallel port bracket. The parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode. English 26 25 JLPT1 2 1 PIN 1 3 5 7 9 11 13 SIGNAL RSTB# PRND0 PRND1 PRND2 PRND3 PRND4 PRND5 PIN 2 4 6 8 10 12 14 SIGNAL AFD# ERR# PINIT# LPT_SLIN# GND GND GND PIN 15 17 19 21 23 25 SIGNAL PRND6 PRND7 ACK# BUSY PE SLCT PIN 16 18 20 22 24 26 SIGNAL GND GND GND GND GND Key (No Pin) En-21 M S-7563 M ainboard Jumper Clear CMOS Jumper: JBAT1 There is a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration. W ith the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, set the jumper to clear data. JBAT1 1 1 3 1 3 Keep Data Clear Data Important You can clear CMOS by shorting 2-3 pin while the system is off. Avoid clearing the CMOS while the system is on; it will damage the mainboard. En-22 Slots PCI (Peripheral Component Interconnect) Express Slots The PCI Express slot supports the PCI Express interface expansion card. The PCI Express x 1 slot supports up to 250 MB/s transfer rate. English PCI Express x16 Slot PCI Express x1 Slot PCI (Peripheral Component Interconnect) Slots The PCI slots support LAN cards, SCSI cards, USB cards, and other add-on cards that comply with PCI specifications. At 32 bits and 33 MHz, it yields a throughput rate of 133 MBps. 32-bit PCI Slot Important When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. En-23 M S-7563 M ainboard PCI Interrupt Request Routing The IRQ, acronym of interrupt request line and pronounced I-R-Q, are hardware lines over which devices can send interrupt signals to the microprocessor. The PCI IRQ pins are typically connected to the PCI bus pins as follows: Order 1 PCI Slot 1 PCI Slot 2 INT A# INT B# Order 2 INT B# INT C# Order 3 INT C# INT D# Order 4 INT D# INT A# En-24 BIOS Setup This chapter provides basic information on the BIOS Setup program and allows you to configure the system for optimum use. You may need to run the Setup program when: * An error message appears on the screen during the system booting up, and requests you to run BIOS SETUP. * You want to change the default settings for customized features. English Important 1. The items under each BIOS category described in this chapter are under continuous update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for reference only. 2. Upon boot-up, the 1st line appearing after the memory count is the BIOS version. It is usually in the format: A7563IMS V1. 0 082208 where: 1st digit refers to BIOS maker as A = AMI, W = AWARD, and P = PHOENIX. [. . . ] DIMM - D DR2 DD R DD R DDR2 DDR2 ; DDR DDR - - D I MM 1 Tc-10 ATX 24-Pin ATX1 ATX 24-pin ATX 24-pin ATX 20-pin ATX 20-pin pin 1 pin 13 () pin 111223 pin 24 12 24 1 2 3 4 5 6 7 8 9 10 1 13 11 12 +3. 3V +3. 3V. GND +5V GND +5V GND PWR OK 5VSB +12V +12V +3. 3V 13 14 15 16 17 18 19 20 21 22 23 24 +3. 3V -12V GND PS-ON# GND GND GND Res +5V +5V +5V GND pin 12 pin 13 ATX 12V JPW1 2 4 1 3 1 2 3 4 GND GND 12V 12V JPW1 1. ATX 12V 18 Tc-11 ATX1 MS-75 6 3 RS- VGA IEEE 1394 () LAN CS- DVI-D DisplayPort USB SS- PCIE x16 VGA, DisplayPort HDMI / P S / 2 ® / D I N P S / 2 ® / VGA ( ) D B 1 5 - p i n DVI-D D VI - D ( - ) L C D D VI -D L C D D V I - D ( ) USB U S B ( ) DisplayPort Di spla yPortD i spl a yPort IEEE 1394 ( ) I E E E 1 3 9 4 I E E E 1 3 9 4 Tc-12 LAN R J - 4 5 LED LED Off LAN LAN 10 Mbit 100 Mbit 1000 Mbit On () On () Off On On () C D () ( ) RS-() 4/5. 1/7. 1 CS-() / 5. 1/7. 1 SS-() 7 . 1 Tc-13 MS-75 6 3 FDD1 360KB720KB1. 2MB1. 44MB 2. 88MB FDD1 IDE IDE1 IDE IDE IDE1 IDE / IDE Tc-14 Serial ATA SATA 1~SATA4 SATA SATA2 SATA4 SATA1 SATA3 Serial ATA 90 Tc-15 MS-75 6 3 CPUFAN1, SYSFAN1/2 + 1 2 V +1 2 V ; G ND C P U GND +12V SENSOR Control SENSOR +1 2V GND CPUFAN1 SYSFAN1/2 1. CPUFAN1/ SYSFAN1/ SYSFAN2 BIOS H/W Monitor Dual Core Center CPU 3. [. . . ]