User manual MSI G52-75301X3 V1.0

[. . . ] P7NGM-Digital Series MS-7530 (V1. X) Mainboard G52-75301X3 i Copyright Notice T he material in this doc ument is the intellec tual property of M ICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trademarks of NVIDIA Corporation in the United States and/or other countries. [. . . ] The system will record this status and show a warning message on the screen. To clear the warning, you must enter the BIOS utility and clear the record. 1 CINTRU GND CD-In Connector: JCD1 This connector is provided for external audio input. L GND R En-18 Front USB Connector: JUSB1~3 This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras, M P3 players, printers, modems and the like. Pin Definition PIN 2 1 10 9 1 3 5 7 9 SIGNAL VCC USB0USB0+ GND Key (no pin) PIN 2 4 6 8 10 SIGNAL VCC USB1USB1+ GND NC English JUSB1~3 USB 2. 0 Bracket (optional) Important Note that the pins of VCC and GND must be connected correctly to avoid possible damage. Serial Port Connector: JCOM1 This connector is a 16550A high speed communication port that sends/receives 16 bytes FIFOs. You can attach a serial device. Pin Definition PIN 9 1 2 3 4 5 6 7 8 9 SIGNAL DCD SIN SOUT DTR GND DSR RTS CTS RI DESCRIPTION Data Carry Detect Serial In or Receive Data Serial Out or Transmit Data Data Terminal Ready Ground Data Set Ready Request T Send o Clear To Send Ring Indicate 2 1 En-19 M S-7530 M ainboard IEEE1394 Connector: J1394_1 (optional) This connector allows you to connect the IEEE1394 device via an optional IEEE1394 bracket. Pin Definition PIN 1 2 1 10 9 3 5 7 9 SIGNAL TPA+ Ground TPB+ Cable power Key (no pin) PIN 2 4 6 8 10 SIGNAL TPAGround TPBCable power Ground IEEE1394 Bracket (optional) TPM Module Connector: JTPM1 (optional) This connector connects to a TPM (Trusted Platform Module) module (optional). Please refer to the TPM security platform manual for more details and usages. 2 1 14 13 Pin 1 3 5 7 9 11 13 Signal LCLK LRST# LAD0 LAD1 LAD2 LAD3 LFRAME# Description LPC clock LPC reset LPC address & data pin0 LPC address & data pin1 LPC address & data pin2 LPC address & data pin3 LPC Frame Pin 2 4 6 8 10 12 14 Signal 3V_STB VCC3 SIRQ VCC5 KEY GND GND Description 3V standby power 3. 3V power Serial IRQ 5V power No pin Ground Ground En-20 Front Panel Connectors: JFP1, JFP2 English These connectors are for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide. JFP1 Pin Definition PIN Power Power LED Switch 1 2 10 9 3 4 5 6 7 8 9 SIGNAL HD_LED + FP PWR/SLP HD_LED FP PWR/SLP RST_SW PWR_SW + RST_SW + PWR_SW RSVD_DNU DESCRIPTION Hard disk LED pull-up MSG LED pull-up Hard disk active LED MSG LED pull-up Reset Switch low reference pull-down to GND Power Switch high reference pull-up Reset Switch high reference pull-up Power Switch low reference pull-down to GND Reserved. Do not use. + 2 1 2 1 Power LED Parallel Port Header: JLPT1 This connector is used to connect an optional parallel port bracket. The parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode. 26 25 PIN 1 3 5 7 9 11 2 1 13 SIGNAL RSTB# PRND0 PRND1 PRND2 PRND3 PRND4 PRND5 PIN 2 4 6 8 10 12 14 SIGNAL AFD# ERR# PINIT# LPT_SLIN# GND GND GND PIN 15 17 19 21 23 25 SIGNAL PRND6 PRND7 ACK# BUSY PE SLCT PIN 16 18 20 22 24 26 Pin) SIGNAL GND GND GND GND GND Key (No + + HDD Reset LED Switch JFP1 JFP2 Pin Definition Speaker PIN 8 7 1 2 3 4 5 6 7 8 SIGNAL GND SPKSLED BUZ+ PLED BUZNC SPK+ DESCRIPTION Ground SpeakerSuspend LED Buzzer+ Power LED BuzzerNo connection Speaker+ + - JFP2 + En-21 M S-7530 M ainboard Jumper Clear CMOS Jumper: JBAT1 There is a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration. W ith the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, set the jumper to clear data. 3 3 1 1 1 JBAT1 Keep Data Clear Data Important You can clear CMOS by shorting 2-3 pin while the system is off. Avoid clearing the CMOS while the system is on; it will damage the mainboard. En-22 Slots PCI-E (Peripheral Component Interconnect-Express) Slot The PCI Express slots are compliant with PCIE 2. 0 spec and support the PCI Express interface expansion card. The PCI Express x1 slot supports up to 500 MB/s transfer rate. English PCI Express x16 Slot PCI Express x1 Slot PCI (Peripheral Component Interconnect) Slot The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that comply with PCI specifications. 32-bit PCI Slot Important When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. PCI Interrupt Request Routing The IRQ, acronym of interrupt request line and pronounced I-R-Q, are hardware lines over which devices can send interrupt signals to the microprocessor. The PCI IRQ pins are typically connected to the PCI bus pins as follows: Order 1 PCI Slot 1 PCI Slot 2 INT Y# INT Z# Order 2 INT Z# INT W# Order 3 INT W# INT X# Order 4 INT X# INT Y# En-23 M S-7530 M ainboard Hybrid SLI Technology Hybrid SLI technology, based on NVIDIA's industry-leading SLI technology, delivers multi-GPU benefits when an NVIDIA mainboard GPU is combined with an NVIDIA discrete GPU. System Requirement 1. For best GeForce Boost performance, the following minimum system configuration is recommended: - AMD Phenom CPU or Intel CPU running at FSB 1333 MHz or higher - 2 x 1 GB of DDR2-800 or higher DRAM - Discrete GPU recommended for GeForce Boost - At least 256 MB of framebuffer carve out for the mainboard GPU. Please select 256 MB in VGA Share Memory field of Advanced BIOS Features in BIOS. Enabling Hybrid SLI Technology Power off the system and install the NVIDIA SLI graphic card that supports Hybrid SLI technology. After then, power on the system and install the driver of Hybrid SLI technology. Restart the system and wait for the Hybrid Icon to show in the System Tray. The hybrid icon indicates that the system is in Performance mode and that GeForce Boost is enabled. The chipset will share the rendering load with the graphic card and boost the performance of the graphic card. Hybrid-Performance M ode - The hybrid mode where the discrete GPU (dGPU) and mainboard GPU (mGPU) are simultaneously active and working collaboratively to provide higher performance (GeForce Boost) Important Hybrid SLI Enabled Graphics Cards GeForce Boost GeForce 8500 GT X GeForce 8400 GS X HybridPower More details please refer to http://www. nvidia. com/object/hybrid_sli. html En-24 BIOS Setup This chapter provides basic information on the BIOS Setup program and allows you to configure the system for optimum use. You may need to run the Setup program when: * An error message appears on the screen during the system booting up, and requests you to run BIOS SETUP. * You want to change the default settings for customized features. English Important 1. The items under each BIOS category described in this chapter are under continuous update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for reference only. [. . . ] Tc-8 DIMM () : http://global. msi. com. tw/index. php?func=testreport DDR2 240-pin, 1. 8V 56x2=112 pin 64x2=128 pin 1 DIMM1 DIMM2 DIMM3 DIMM4 2 DIMM1 DIMM2 DIMM3 DIMM4 Tc-9 MS-7530 1. DIMM V - DDR2 DDR DDR DDR2 DDR2 ; DDR DDR - - DIMM1 - DIMM 2GB 7+GB ( 8 GB ) Tc-10 ATX 24-Pin JPWR1 ATX 24-pin ATX 24-pin ATX 20-pin ATX 20-pin pin 1 pin 13 () pin 111223 pin 24 12 24 1 2 3 4 5 6 7 8 9 10 1 13 11 12 +3. 3V +3. 3V. GND +5V GND +5V GND PWR OK 5VSB +12V +12V +3. 3V 13 14 15 16 17 18 19 20 21 22 23 24 +3. 3V -12V GND PS-ON# GND GND GND Res +5V +5V +5V GND pin 13 pin 12 ATX 4-pin JPWR2 4 3 2 1 1 2 3 4 GND GND 12V 12V 1. 350 () Tc-11 MS-7530 nForce (ESD, Electrostatic Discharge) S5 () () () : : : Tc-12 VGA IEEE 1394 () LAN RS- CS- HDMI DVI-D USB USB SS- / PS/2 ® / DIN PS/2 ® / HDMI (HDMI)/ HDMI HDMI-out HDMI VGA DB15-pin DVI-D DVI-D (-) LCDDVI-D LCD DVI- D () IEEE 1394 () IEEE1394 IEEE1394 Tc-13 MS-7530 USB USB () LAN R J - 4 5 LED LED Off On () On () Off On On LAN LAN 10 Mbit 100 Mbit 1000 Mbit () C D () () RS-() 4/5. 1/7. 1 CS-() / 5. 1/7. 1 SS-() 7 . 1 Tc-14 FDD1 360KB720KB1. 2MB1. 44MB 2. 88MB IDE IDE1 IDE IDE IDE / IDE Tc-15 MS-7530 Serial ATA SATA 1~6 SATA SATA SATA6 SATA4 SATA2 SATA5 SATA3 SATA1 Serial ATA 90 Tc-16 CPUFAN1, SYSFAN1 +12V +12V; GND CPU CONTROL SENSOR +12V GND NC +12V GND CPUFAN1 SYSFAN1 1. [. . . ]