User manual LIFT-MASTER STAR450-315
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LIFT-MASTER STAR450-315. We hope that this LIFT-MASTER STAR450-315 user guide will be useful to you.
Manual abstract: user guide LIFT-MASTER STAR450-315
Detailed instructions for use are in the User's Guide.
[. . . ] STAR450-315TM WIRELESS ACCESS CONTROL RECEIVER
SPECIFICATIONS SUPPLY VOLTAGE: 12-24 VOLTS AC OR DC OPERATING CURRENT: 250 mA MAXIMUM OPERATING TEMP RANGE: -40 TO +149F (-40 TO +65C) FREQUENCY: 315 MHz RELAY CONTACT RATING: 1 AMP @ 24 VOLTS AC OR DC
WARNING CAUTION
WARNING WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution: · Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: · ALWAYS keep remote controls out of reach of children. · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. [. . . ] Direct Antenna Mounting: Install the provided antenna onto the STAR450 antenna connector by screwing the connector clockwise. Slide the seal boot down to meet the O-ring, covering the antenna hardware. Remote Antenna Mounting: Use the optional 86LM antenna extension kit to mount the remote antenna as high and far from metal as possible for best radio range (Figure 2). Contact LiftMaster customer service at: 1-800-528-2806 to order the model 86LM. Figure 1
Antenna Seal Boot
Antenna Connector
Figure 2
STAR450 FEATURES
POWER INDICATOR SCROLLING DASHES ON DIGITAL DISPLAY WHEN AC OR DC POWER IS APPLIED TO THE UNIT.
DIGITAL DISPLAY DISPLAYS REMOTE CONTROL LOCATION NUMBERS WHEN PROGRAMMING OR ACCESS IS GRANTED. ALSO DISPLAYS USER PROMPTS AND MESSAGES.
DELETE KEY USED TO DELETE A REMOTE CONTROL FROM THE SELECTED MEMORY LOCATION
ANTENNA CONNECTION FOR CONNECTION TO THE DIRECT ANTENNA OR THE ANTENNA EXTENSION KIT. BLOCK KEY USED TO BLOCK THE RECEIVER FROM GRANTING ACCESS TO THE SELECTED REMOTE CONTROL. REMOTE CONTROL REMAINS IN MEMORY, AND MAY BE UNBLOCKED IN THE FUTURE.
Add
ADD KEY USED TO ENTER REMOTE CONTROLS AND ENTER RAPID LEARNTM MODE.
Delete
Block
1 4 7 *
2 5 8 0
3 6 9
#
NUMERIC KEYPAD USED FOR PROGRAMMING AND QUERYING REMOTE CONTROL LOCATIONS. ALSO USED TO ENTER ADVANCED FUNCTIONS.
STAR KEY USED TO ENTER ADVANCED FUNCTIONS: , 1- LAST REMOTE CONTROL RECEIVED , 2- NO. OF BLOCKED REMOTE CONTROL LOCATIONS , 5- FIRST BLOCKED REMOTE CONTROL LOCATION , 7- SOFTWARE VER. # , 0- AUDIBLE DIAGNOSTICS OFF/ON
POUND KEY USED AS AN ESC OR EXIT KEY FOR ALL FUNCTIONS OR MODES.
PROGRAMMING THE STAR450
Rapid LearnTM: Add remote control to next available location.
AUTO
001
Add PRESS PRESS
#
PRESS
TO EXIT
Add
Adding Remote Control: Add remote control to a specific location.
AUTO
001
Add PRESS
002
2
023
3
234
4
PRESS
#
PRESS
TO EXIT
ENTER LOCATION (1-450)
Add
Deleting a Remote Control: To delete a user.
Del
Delete
PRESS
002
2
023
3
234
4
Delete
PRESS TO CONFIRM
Del
END
ENTER LOCATION (1-450)
2
PROGRAMMING THE STAR450 (CONT'D)
Blocking (Unblocking) a Remote Control: To block or unblock a user.
bLc
Block PRESS
002
2
023
3
234
4
Block PRESS TO CONFIRM
bLc
END (UNBLOCK)
ENTER LOCATION (1-450)
Un-
bLc
Duplicating Memory: Allows user to backup programmed remote control memory into the provided backup memory module. Note: If two memory modules are installed, press , 6 to duplicate the memory and remove the backup module.
Main Memory Module
dup
, PRESS SIMULTANEOUSLY
Backup Memory Module
*
6
END ~6 SECONDS
Note: To duplicate memory, plug backup memory module into backup slot and press , 6. Once duplication is complete, remove the backup memory module and store in a separate location. Restoring Memory: To restore memory, simply place the duplicate memory module in the main memory position. ADVANCED FUNCTIONS For advanced functions, press and hold the key and a number key at the same time to select the corresponding advanced function. (See table at right for available functions. ) Press the # key to exit the function.
* 1 Memory location of last remote control received. [. . . ] If unit exhibits this condition again after 2 minutes, contact Technical Service.
ELECTRICAL CONNECTIONS FOR STAR450
Receiver (Bottom) Wall Button Receiver (Bottom) Wall Button Opener Trans Primary Trans Primary
Model 85 Transformer To wall outlet
To wall Model 95 outlet Transformer
STAR450 COMPATIBLE REMOTE CONTROLS
Security+® Remote Controls
371LM 372LM 370LM 373LM 374LM
STAR450 OPTIONAL ACCESSORIES
CGI Part Number
71-65WTBOX 86LM 85LM 95LM
Security+® Keypads
376LM
Description
Watertight Box Field Install Kit Antenna Extension Kit 24VAC Transformer with Barrel Connector 24VAC Transformer with Screw Terminals
PassportTM Remote Control
CPT43 CPT13 CPT23 CPT33
Digital Remote Controls
361LM 362LM 363LM
HOW TO ORDER REPAIR PARTS
OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE 6 DAYS A WEEK. CALL OUR TOLL FREE NUMBER: 1-800-528-2806 MONDAY Through FRIDAY 5:00 a. m. (MST) www. liftmaster. com
PassportTM Mini Remote Control
CPTK13 CPTK13PH CPTK33 CPTK33PH For highest level of security, we recommend the Security+® transmitter family.
114A3254B
© 2006, The Chamberlain Group, Inc. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER STAR450-315
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER STAR450-315 will begin.