User manual KORG SGPROX

[. . . ] AI Synthesis System 2 ASSIGNABLE WHEEL AW1 AW2 VOLUME LOW LOW-MID EQUALIZER MID HIGH-MID HIGH AL1/A ASSIGNABLE SLIDER AL2/a AL3/0 AL4/!SPLIT LAYER SINGLE VALUE EFFECT ON EFFECT OFF PERF EDIT CONTROLLER BRIGHTNESS VEL CURVE LEVEL FX1 PARAM PIANO2 CHANNEL LOCAL VEL CURVE PROGRAM EX FILTER A. T CURVE SW/ CHANNEL A. T CURVE ATTACK FX2 TYPE PIANO3 AFT. T FILT PROG PROTECT LEVEL TIMB COPY DECAY FX2 PARAM E. PIANO1 DAMP. P POL PERF PROTECT PITCH CTRL COPY RELEASE SCALE /BEND E. PIANO2 ASGN. SW POL PAGE MEM PANPOT MACRO KEY TOUCH PRELOAD E. PIANO3 DATA DUMP SYS NAME ZONE RENAME FX1 DEPTH RENAME PF LAYER MIDI RESET CALIB FILTER WRITE FX2 DEPTH WRITE E. P. LAYER GLOBAL CONTROLLER TIMBRE SEL BANK MASTER TUNE TRANSPOSE NORMAL PROG EDIT FX1 TYPE PIANO1 PERFORMANCE A a DELETE INSERT CURSOR PROGRAM ORGAN1 ORGAN2 COMP BELL/VIBES STRINGS PAD1 PAD2 BASS 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 Owner's Manual E 3 Introduction IMPORTANT SAFETY INSTRUCTIONS WARNING — When using electrical products, basic precautions should be followed, including the following: 1. Do not use this product near water — for example, near a bathtub, sink, in a wet basement, or near a swimming pool, etc. This product should be used only with additional hardware that is recommended by the manufacturer. [. . . ] If you wish to keep an edited program, you must Write it ( p. 37). Parameter value Structure of the Program Edit mode RENAME WRITE PROGRAM SCALE BRIGHTNESS ATTACK DECAY RELEASE KEY TOUCH Basic sound LEVEL Control signal Audio signal FX1 TYPE PARAM DEPTH FX2 TYPE PARAM DEPTH OUTPUT 33 Program Edit mode 1. BRIGHTNESS (Brightness setting) This parameter adjusts the brightness of the sound. Negative (–) settings will cut the high frequency range, making the tone softer and darker. Positive (+) settings will increase the volume, and negative (–) settings will decrease it. Range of settings Factory setting –99 to +99 +00 For some sounds, increasing the Level setting may cause the sound to be distorted when chords are played. If this occurs, reduce the level. Volume Key-on Key-off The three following parameters are Envelope Time settings. Negative (–) settings will shorten the time and positive (+) settings will lengthen the time. Release time Time Attack time Decay time 3. ATTACK (Attack time setting) This parameter specifies the time from the key-on until the maximum volume is reached. It can can be adjusted to create fast and slow attack strings sounds etc. DECAY (Decay time setting) This parameter specifies the time over which the volume will decay while you continue to press the key. RELEASE (Release time setting) Release This parameter specifies the time from when the note is released until the volume decays. Range of settings Factory setting –99 to +99 +00 Damper mode For conventional piano and electric piano sounds, set this to “PIANO. ” For other sounds, set this to “Nomal. ” PIANO In addition to normal operation (decay will be slow while the pedal is pressed), pressing the damper pedal during the release (while a released note is decaying) will cause the decay to be slower (redamp). If a pedal that supports half-damping (DS-1H recommended) is used, the degree to which the pedal is pressed will regulate the decay time. NORMAL Normal operation (decay will be slow while the pedal is pressed), and redamping will not occur. Damper Mode High Notes Damp 34 Program Edit mode High note damp In the high note range of A6 and above, notes will always sound as though the damper pedal were being pressed, regardless of the actual operation of the damper pedal. NORMAL Even in the high note range of A6 and above, notes will sound in the same way as lower notes (i. e. , they will decay more slowly while the damper pedal is pressed). KEY TOUCH (Key touch setting) This parameter specifys how the force with which you play the keyboard will affect changes in volume and tone. With positive (+) settings, your playing dynamics will produce greater change in volume and tone. With negative (–) settings, the volume and tone will be constant, regardless of your keyboard playing dynamics. FX1 DEPTH (FX1 effect balance setting) This parameter sets the balance between the original sound and effect 1. However if no effect is selected for FX1, the display will indicate “NO EFFECT. ” Range of settings DRY, 99:01 to 01:99, FX When “Hyper Enhancer” is selected as the FX1 effect type, only “DRY” or “FX” can be selected. 8. FX2 DEPTH (FX2 effect balance setting) This parameter sets the balance between the original sound and effect 2. However if no effect is selected for FX2, the display will indicate “NO EFFECT. ” Range of settings DRY, 99:01 to 01:99, FX ❋ The display when No Effect is selected for FX2 9. [. . . ] ( p. 27) Does the MIDI channel of the messages being transmitted by the external device match the Global MIDI channel (set in Global mode) of the SGproX?( 27) q In a keyboard split performance, are you playing an area of the keyboard that produces no sound?( p. 15) q q q q q Sound does not stop! q Is the damper polarity setting correct?( p. 28) q On sustain-type programs such as strings or organ, has the Damper mode been set to “PIANO”? [. . . ]