User manual KORG MINI KAOSS PAD 2

[. . . ] Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, or cleaning compounds or flammable polishes. Keep this manual After reading this manual, please keep it for later reference. Keeping foreign matter out of your equipment • Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire, or electrical shock. [. . . ] The pitch of OSC1 will be the pitch that sounds when you use the keyboard function or the pitch specified for a phrase pattern. OSC1 Wave Specify the basic waveform of OSC1. (sawtooth wave) This waveform is rich in overtones, and is suitable for bass or synth lead sounds. (square wave) This waveform contains only the odd-numbered har monics, and produces a tone typical of electronically produced sound. (triangle wave) This waveform is more mellow than the sawtooth wave or square wave, and is suitable for sub-bass sounds etc. Audio In The audio signal input from the audio input jack will be used as OSC1. So that they will be particularly suitable for bass sounds, the waveforms of OSC1 have a slightly heavier sound (fundamental) than the waveforms of OSC2. OSC2 Wave Specify the basic waveform of OSC2 (refer to OSC1 Wave). When OSC Mod is set to Deci, the basic waveform selection will have no effect. OSC Mod (oscillator modulation) off, Ring, Sync, Deci Select the type of modulation that will occur between the oscillators. Since OSC2 will be modulated (i. e. , it will be the slave), the results of the modulation will be output from OSC2. For either of the types of oscillator modulation, using a motion sequence etc. • Off (When the OSC Mod LED is dark) OSC 1 WAVE OSC 2 WAVE When OSC Mod is off, the oscillators will not modulate each other. By using OSC2 Pitch Ofs to create a slight difference in pitch between the oscillators, you can produce a spacious detune effect. The EG will start when trigger-on occurs (the instant you play the keyboard). If the gate time length of a step extends beyond the point at which the next step is sounded, the EG will not be re-triggered for the next step. Chorus/Flanger settings Set the Type Select button to Chorus/Flanger, and adjust the chorus/flanger. Chorus creates minute differences in the pitch to produce an ensemble effect, and Flanger adds a "swooshing" modulation to the sound. • Depth (chorus/flanger depth) 0. . . 100 Decay 0 msec . . . In conjunction with the Cutoff and EG Int parameters, this controls the way in which the sound will change over time. If EG Int is set to a negative (–) setting, Decay Time can be used in place of Attack Time. Adjust the depth of the chorus/flanger effect. Rotating the knob toward the right will change from a chorus effect to a flanger effect. Raising the depth excessively may cause the sound to distort. Time (LFO rate) 0. 2 Hz . . . Rotating the knob toward the right will speed up the LFO. 4. Pattern mode Length, Scale/Beat settings You can set the length (the length of the entire pattern) and the basic beat (time signature). The Length and Scale/Beat you specify here will affect the correspondence between step keys and note values, and the maximum number of steps as shown in the following diagram. While you hold down the Shift key, the step keys will light to indicate the length and beat of the current pattern. To change the Length, hold down the Shift key and press a Step Key 1. . . 4. To change the Beat/Scale, hold down the Shift key and press a Step Key 5. . . 7. [. . . ] (p. 40) Playing the step keys does not sound the specified sound! • After editing the sound of a part, did you perform the Write operation?(p. 29) Error messages Er. 1 Er. 2 Er. 9 Full Data could not be written. When writing a song to a different song number, the maximum number of recordable events was exceeded. Protect was turned "on" for the memory into which you attempted to write data. [. . . ]