User manual KORG KSERIES

[. . . ] 23 Owner’s Manual Precautions Location Using the unit in the following locations can result in a malfunction. € In direct sunlight • Locations of extreme temperature or humidity • Excessively dusty or dirty locations • Locations of excessive vibration • Close to magnetic fields • Reorient or relocate the receiving antenna. € Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. € Consult the dealer or an experienced radio/ TV technician for help. [. . . ] The assignable values are “No Assign/Control Change/Mouse”. 127] Moving the ClickPoint controller will change the value of the parameters assigned to the X and Y axis The ClickPoint controller will return to the center position when it’s released. To lock the X and Y parameters at their current values, press down (Z axis) on the center switch of the ClickPoint. Mouse Mode When set to “Mouse” mode, the ClickPoint can be operates as a mouse and will control the cursor on computer screen. The Mouse Mode is only operative when the connected to a computer via USB. KNOB1 and KNOB2 By assigning MIDI control changes, these knobs can be used to operate external MIDI equipment and control musical software applications. 127] Turning the knob will change the value of the assigned parameter. 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Owner’s Manual SW1 and SW2 These two switches can be assigned individually to send a specific value to a specific MIDI control change parameter. In fact, both an “on” and “off” value can be set. The assignable values on SW1 and SW2 are “No Assign/Program Change/Control Change”. Program Change Every time [SW1] is pressed, the program change number is decreased by 1. Every time [SW2] is pressed, the program change number is increased by 1. In addition, a program change message of “0” is sent if [SW1] are [SW2] are pressed simultaneously. In “Toggle” mode, each time a switch is pressed, a MIDI control message is sent; each press will alternate between the On Value and the Release Value. In “Momentary” mode, the On Value MIDI control message is sent when the switch is pressed down, and a Off Value MIDI control message is sent when the switch is released. — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ OCTAVE SHIFT UP / OCTAVE SHIFT DOWN These buttons can shift pitch of the keyboard in one octave units. — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 13 MOD wheel By assigning a MIDI control change number, the Modulation Wheel can be used to operate external MIDI equipment and control musical software applications. The assignable values are “No Assign/Control Change/After touch”. 127] Use the Mod Wheel to smoothly change the value of the assigned MIDI control change parameter. — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ SLIDER By assigning a MIDI control change number, the Modulation Wheel can be used to operate external MIDI equipment and control musical software applications. 127] Use the slider to smoothly change the value of the assigned MIDI control change parameter. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ PEDAL An optional pedal switch can be assigned to send a specific value to a specific MIDI control change parameter. [. . . ] Depending on the hardware setup of your computer, it may not be possible for the K-Series to be recognized via a USB connection. € It may be that the connected device or software does not support the function you’re attempting to use. Refer to the owner’s manual of the connected device or software, and make sure that the function is supported.  No sound(K61P) • Make sure the K-Series’ volume is not set to “0”. [. . . ]