User manual KENWOOD KTC-1000R
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD KTC-1000R. We hope that this KENWOOD KTC-1000R user guide will be useful to you.
You may also download the following manuals related to this product:
KENWOOD KTC-1000R (143 ko)
Manual abstract: user guide KENWOOD KTC-1000R
Detailed instructions for use are in the User's Guide.
[. . . ] · To prevent short circuits when replacing a fuse, first disconnect the wiring harness. · During installation, do not use any screws except for the ones provided. · When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. [. . . ] · Insulate unconnected cables with vinyl tape or other similar material. · During use, the surface temperature of this unit will become high, therefore it should not be mounted where anything sensitive to the heat, such as people or resins, would come into contact with it. · Install this unit in a location which allows heat to easily dissipate. · Install the unit securely in a location that does not interfere with driving.
English
3
Installation
s Connecting Cables to Terminals
2WARNING
If you connect the ignition cable (red) and the battery cable (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those cables to the power source running through the fuse box. Front left output (White)
PREOUT
REAR/NON-FAD FRONT
NOTE
Do not put anything into the fuse holder.
TO 5L I/F
TO MZ-BUS
Rear left output (White) / Non-fading left output (White) Rear right output (Red) / Non-fading right output (Red) Front right output (Red) FM/AM antenna input
DAB
FM·AM TUNER 44W×4 AMPLIFIER HIDEAWAY UNIT
KTC-1000R
FM ANTENNA FRONT SPEAKER
REAR SPEAKER TV MONITOR
SUB WOOFER
CHANGER SLAVE UNIT
ANTENNA INPUT
PREOUT
REAR/NON-FAD FRONT
POWER
Antenna Conversion Adaptor (ISOJASO) (Accessory8) Antenna Cord (ISO)
(5. 5m)
Antenna Cord (Accessory6)
NOTE
Route wiring away from power circuitry to avoid noise.
Wiring harness (5. 5m) (Accessory5) Connector A Connector B
8 7 8 7 6 5 6 5 4 3 4 3 2 1 2 1 Automatic illumination control cable (Orange)
ILLUMI
Ignition cable (Red)+12V
ACC ACC
Fuse (3A)
ACC
Connect to control unit power supply terminal.
Battery cable (Yellow)+12V
BATT BATT
Fuse (10A)
BATT
When using the optional power amplifier, connect to its power control terminal. Connect to the terminal that is grounded when either the telephone rings or during conversation.
NOTE
Power control cable (Blue/ White)
P. CONT
TEL mute cable (Brown)
TEL MUTE
To connect the KENWOOD navigation system, consult your navigation manual.
Ground cable (Black) (To car chassis) If no connections are made, do not let the cable come out from the tab.
4
English
2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated.
Connector Function Guide
Pin Numbers for Cable Colour ISO Connectors
Functions
1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. A7 Pin (Red) Ignition cable (Red)
ACC BATT ACC BATT
External Power Connector A4 A5 A6 A7 Speaker Connector B1 B2 B3 B4 B5 B6 B7 B8
Yellow Blue/White Orange Red
Battery Power Control Dimmer Ignition (ACC)
Vehicle
Unit
A4 Pin (Yellow)
Control unit Battery cable (Yellow)
ACC BATT
Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black
Rear Right (+) Rear Right () Front Right (+) Front Right () Front Left (+) Front Left () Rear Left (+) Rear Left ()
2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. A7 Pin (Red) Ignition cable (Red)
ACC
Vehicle
ACC
Unit
BATT BATT
A4 Pin (Yellow)
Control unit Battery cable (Yellow)
ACC BATT
3 The A-7 pin (red) of the vehicle's ISO connector is not connected to anything, whilst the A-4 pin (yellow) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Connect to a power source that can be turned on and | off with the ignition key. BATT Vehicle A4 Pin (Yellow) Ignition cable (Red)
BATT
Unit
Control unit Battery cable (Yellow)
BATT
English
5
Installation
s When the control unit is the KVC-1000
Control unit (optional) KVC-1000
M4 IN OUT NAV I/F
DAB control cable (Provided with the KTC-959DAB) KTC-1000R
ANTENNA INPUT
DAB
DAB tuner (optional)
KTC-959DAB
Changer control cable (Provided with the C907)
2WARNING
CD auto changer (optional) C907
Only connect black cable to TO 5L interface. [. . . ] · The ignition and battery cable are incorrectly connected.
The following indications are used to inform you that there is a problem with the connections of the system. BUS-E01: The M-S switch of the Monitor connected to the BUS terminal is set to "M". The "MASTER SW" cable of the monitor power supply harness is connected to -. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD KTC-1000R
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD KTC-1000R will begin.