User manual JVC KD-D2

[. . . ] To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all electrical connections before installing the unit. Be sure to ground this unit to the car's chassis again after installation. It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 to 8 ). [. . . ] If the maximum power is less than 50 W, change "Amp Gain" setting to prevent the speakers from being damaged (see page 48 of the INSTRUCTIONS). To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape. If any item is missing, consult your JVC IN-CAR ENTERTAINMENT dealer immediately. If you have any questions or require information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits. Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit. If you are not sure how to install this unit correctly, have it installed by a qualified technician. When using the optional stay / Beim Verwenden der Anker-Option / Lors de l'utilisation du hauban en option / Wanneer u de steun gebruikt (facultatief) When installing the unit without using the sleeve / Beim Einbau des Geräts ohne Halterung / Lors de l'installation de l'appareil scans utiliser de manchon / Wanneer u het apparaat zonder huis installeert In a Toyota car for example, first remove the car radio and install the unit in its place. Flat head screws (M5 × 8 mm) *2 Flachkopfschrauben (M5 × 8 mm) *2 Vis à tête plate (M5 × 8 mm) *2 Schroeven met platte kop (M5 × 8 mm) *2 Bracket *2 Konsole *2 Support *2 Console *2 Flat head screws (M5 × 8 mm) *2 Flachkopfschrauben (M5 × 8 mm) *2 Vis à tête plate (M5 × 8 mm) *2 Schroeven met platte kop (M5 × 8 mm) *2 Bracket *2 Konsole *2 Support *2 Console *2 Note Install the unit at an angle of less than 30°. When installing the monitor in a location where it can be seen by the driver Connect the parking brake wire to the parking brake system built in the car. When installing the monitor in a location where it cannot be seen by the driver Connect the parking brake wire to metallic body or chassis of the car. Connectez le fil de commande à distance (bleu avec bande blanche) au fil de commande à distance de l'autre appareil de façon qu'il puisse être commandé via cet appareil. Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit. Disconnect the speakers from this unit, connect them to the amplifier. Remote lead (blue with white stripe) Fernbedienungsleitung (blau mit weißem Streifen) Fil d'alimentation à distance (bleu avec bande blanche) Afstandbedieningsdraad (blauw met witte streep) To the remote lead of other equipment or power aerial if any Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern vorhanden Au fil de télécommande de l'autre appareil ou à l'antenne automatique s'il y en a une Naar afstandsdraad van andere apparatuur of antenne met circuit indien aanwezig Remote lead Not supplied for this unit. Signal cord (not supplied for this unit) Firmly attach the ground wire to the metallic body or to the chassis of the car--to the place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Cut the rear speaker leads of the car's ISO connector and connect them to the amplifier. [. . . ] Cut the rear speaker leads of the car's ISO connector and connect them to the amplifier. Before connecting the external components, make sure that the unit is turned off. You can also connect the following components through the various JVC adapters. [. . . ]