User manual INTEL D815EEA2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual INTEL D815EEA2. We hope that this INTEL D815EEA2 user guide will be useful to you.


INTEL D815EEA2 : Download the complete user guide (934 Ko)

Manual abstract: user guide INTEL D815EEA2

Detailed instructions for use are in the User's Guide.

[. . . ] Intel® Desktop Board D815EEA2/D815EPEA2 Technical Product Specification May 2001 Order Number A46399-002 The Intel® Desktop Boards D815EEA2 and D815EPEA2 may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board D815EEA2/D815EPEA2 Specification Update. Revision History Revision -001 -002 Revision History First release of the Desktop Board D815EEA2/D815EPEA2 Technical Product Specification Second release of the Intel® Desktop Board D815EEA2/D815EPEA2 Technical Product Specification Intel® Date February 2001 May 2001 This product specification applies to only standard D815EEA2 and D815EPEA2 boards with BIOS identifier EA81520A. 86A. Changes to this specification will be published in the Intel Desktop Board D815EEA2/ D815EPEA2 Specification Update before being incorporated into a revision of this document. Information in this document is provided in connection with Intel® products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. [. . . ] The LED will indicate when data is being read or written using the add-in controller. Table 47 lists the signal names of the SCSI hard drive activity LED connector. Table 47. Pin 1 2 SCSI LED Connector (J8H2) Signal Name SCSI activity Not connected 79 Intel Desktop Board D815EEA2/D815EPEA2 Technical Product Specification 2. 8. 3. 3 Front Panel Connector This section describes the functions of the front panel connector. Table 48 lists the signal names of the front panel connector. Table 48. Pin 1 3 5 7 9 11 13 15 Front Panel Connector (J9H3) In/Out Out Out Description Hard disk LED pullup (330 ) to +5 V Hard disk activity LED Ground In Out Reset switch Power Reserved Ground Reserved Pin 2 4 6 8 10 12 14 16 Signal HDR_BLNK_ GRN HDR_BLNK_ YEL FPBUT_IN GND N/C GND (pin removed) +5 V Out In/Out Out Out In Description Front panel green LED Front panel yellow LED Power switch Ground Not connected Ground Not connected Power Signal HD_PWR HDA# GND FP_RESET# +5 V N/C GND N/C 2. 8. 3. 3. 1 Reset Switch Connector Pins 5 and 7 can be connected to a momentary SPST type switch that is normally open. When the switch is closed, the D815EEA2 and D815EPEA2 boards reset and run the POST. 2. 8. 3. 3. 2 Hard Drive Activity LED Connector Pins 1 and 3 can be connected to an LED to provide a visual indicator that data is being read from or written to a hard drive. For the LED to function properly, an IDE drive must be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI hard drive activity LED connector. For information about The SCSI hard drive activity LED connector Refer to Section 2. 8. 3. 2, page 79 80 Technical Reference 2. 8. 3. 3. 3 Power/Sleep/Message Waiting LED Connector Pins 2 and 4 can be connected to a single-colored or dual-colored LED. Table 50 shows the possible states for a dual-colored LED. Table 49. LED State Off Steady Green Blinking Green States for a Single-Colored Power LED Description Power off/sleeping Running Running/message waiting Table 50. LED State Off States for a Dual-Colored Power LED Description Power off Running Running/message waiting Sleeping Sleeping/message waiting Steady Green Blinking Green Steady Yellow Blinking Yellow NOTE To use the message waiting function, ACPI must be enabled in the operating system and a messagecapturing application must be invoked. 2. 8. 3. 3. 4 Power Switch Connector Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the D815EEA2 and D815EPEA2 boards. ) At least two seconds must pass before the power supply will recognize another on/off signal. 81 Intel Desktop Board D815EEA2/D815EPEA2 Technical Product Specification 2. 9 Jumper Blocks CAUTION Do not move any jumpers with the power on. Always turn off the power and unplug the power cord from the computer before changing a jumper setting. Figure 17 shows the locations of the jumper blocks on the D815EEA2 and D815EPEA2 boards. 97531 A 10 642 J6B2 3 1 B J9G2 Present only on D815EEA2 boards OM11781 Item A B Description Front panel audio connector / jumper block BIOS Setup configuration jumper block Reference Designator J6B2 J9G2 Figure 17. Locations of the Jumper Blocks 2. 9. 1 · · Front Panel Audio Connector/Jumper Block With jumpers installed, the audio line out signals are routed to the back panel audio line out connector. With jumpers removed, the connector provides audio line out and mic in signals for front panel audio connectors. The connector at location J6B2 has two functions: Table 51 describes the two configurations of this connector/jumper block. CAUTION Do not place jumpers on this block in any configuration other than the one described in Table 51. Other jumper configurations are not supported and could damage the board. 82 Technical Reference Table 51. 9 5 Front Panel Audio Connector / Jumper Block (J6B2) Configuration Audio line out signals are routed to the back panel audio line out connector. The back panel audio line out connector is shown in Figure 13 on page 64. 3 1 Jumper Setting 7 10 6 4 2 5 and 6, 9 and 10 9 7 5 3 1 Audio line out and mic in signals are available for front panel audio connectors. Table 30 on page 70 lists the names of the signals available on this connector when no jumpers are installed. 10 6 4 2 No jumpers installed NOTE When the jumpers are removed and this connector is used for front panel audio, the back panel audio line out and Mic in connectors are disabled. 2. 9. 2 BIOS Setup Configuration Jumper Block This 3-pin jumper block determines the BIOS Setup program's mode. Table 52 describes the jumper settings for the three modes: normal, configure, and recovery. When the jumper is set to configuration mode and the computer is powered-up, the BIOS compares the CPU version and the microcode version in the BIOS and reports if the two match. Table 52. Normal 1-2 Configure 2-3 Recovery None BIOS Setup Configuration Jumper Settings (J9G2) Jumper Setting 3 1 Function/Mode Configuration The BIOS uses current configuration information and passwords for booting. A recovery diskette is required. 3 1 3 1 For information about How to access the BIOS Setup program The maintenance menu of the BIOS Setup program BIOS recovery Refer to Section 4. 1, page 111 Section 4. 2, page 112 Section 3. 7, page 106 83 Intel Desktop Board D815EEA2/D815EPEA2 Technical Product Specification 2. 10 Mechanical Considerations 2. 10. 1 Form Factor The D815EEA2 and D815EPEA2 boards are designed to fit into a standard ATX-form-factor chassis. Figure 18 illustrates the mechanical form factor for the D815EEA2 and D815EPEA2 boards. The outer dimensions are 11. 55 inches by 8. 20 inches [293. 37 millimeters by 208. 28 millimeters]. [. . . ] (See Section 5. 3 for details of different buses. ) Going to do any init before C800 optional ROM control. About to give control to do any required processing after optional ROM returns control and enable external cache. Going to do any initialization required before giving control to optional ROM at E000. Going to do any initialization required after E000 optional ROM control. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE INTEL D815EEA2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual INTEL D815EEA2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.