User manual INFINITY 6000M

[. . . ] · Turn off the audio system and other electrical devices before you start. Disconnect the (­) negative lead from your boat's battery and/or turn off the battery switch if you have a multiple battery setup. · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface and could puncture the boat's hull. [. . . ] Pull this pin up in order to swivel the speaker 270 degrees at 45-degree intervals. Once you have the speaker near the position that you want, release the pin and rotate the speaker until the pin locks in place. Pulling the swivel-lock pin up. CONNECTING THE SPEAKERS Connect the speakers to an amplifier using the supplied speaker wires. The weatherproof connectors allow for quick connection and disconnection of the wires when installing and removing the speakers. Run the wires along the tube and secure in place with plastic zip ties. If the tube has wire holes available, run the speaker wires through the tower tubes to the amplifier. Check to make sure the wires will not come in contact with sharp edges or metal that can damage the wires over time. Swiveling the speaker. 3 MOUNTING THE AMPLIFIER Mount the 6100m or 2100m amplifier in a location that is away from direct contact with water, whether from washing, big waves or soggy riders. Choose a location in the boat where the amplifier will not be damaged by shifting cargo or passengers. If the amplifier is going to be under a seat, ensure that it is clear of all moving parts and will not affect the seat adjustments. If mounting the amplifier in an enclosed space, make sure there is plenty of air circulation for the amplifier to cool properly. POWER CONNECTIONS The 6100m/2100m amplifiers are capable of delivering high power levels, and require a reliable connection to the boat's electrical system in order to perform optimally. Please adhere to the following instructions carefully: GND TERMINAL Connect the amplifier's Ground (GND) terminal directly to the boat's negative (­) battery terminal using a minimum of 8-gauge power wire. +12V TERMINAL Connect a minimum of 8-gauge power wire directly to the boat's positive battery terminal, and install an appropriate fuse holder within 18" of the battery terminal. Route the wire to the amplifier's location, and connect it to the amplifier's positive (+12V) terminal. Be sure to use appropriate grommets whenever routing wires through panels. Failure to adequately protect the positive wire from potential damage may result in a fire. When you are done routing and connecting this wire, you may install the fuse at the battery. NOTE: If your boat uses a multiple battery setup, please contact the boat manufacturer or dealer for proper connection instructions. REMOTE TERMINAL Connect the amplifier's REMOTE terminal to the source unit's Remote Turn-On lead, using a minimum of 18-gauge wire. If your source unit does not have a remote turn-on connection, connect the amplifier's REMOTE terminal to the boat's accessory circuit. NOTE: When using the Hi-level inputs, connect the REMOTE terminal to the source unit. [. . . ] ­ Check speaker connections for proper polarity. Declaration of Conformity SPECIFICATIONS · PROBLEM: Page is distorted. · Frequency Response: 10Hz ­ 40kHz · Signal-to-Noise Ratio: 91dB · Line-Level Input Sensitivity: 250mV ­ 6V · Speaker-Level Input Sensitivity: 6V ­ 16V · Speakers: 11" x 18" x 14-1/2" · Amplifier: 8-1/8" x 8" x 2-3/8" · Microphone: 1-1/4" x 2-1/2" x 3-5/8" · Min. Speaker Impedance: 4 ohms, stereo 6000m · Power Handling: 150W · Peak Power Handling: 450W · Sensitivity: 93dB @ 2. 83V · Frequency Response: 80Hz ­ 20kHz · Impedance: 4 ohms · Polypropylene Cone · Cast-Polymer Basket · CMMDTM Tweeter · Rubber Surrounds · UV-Resistant · Water-Resistant · Salt-Spray-Resistant · 11" x 18" x 14-1/2" 2100m · 125W x 2 ch. @ 4 ohms · Frequency Response: 10Hz ­ 40kHz · Signal-to-Noise Ratio: 91dB · Line-Level Input Sensitivity: 250mV ­ 6V · Speaker-Level Input Sensitivity: 6V ­ 16V · 8-1/8" x 8" x 2-3/8" · Min. [. . . ]