User manual ICOM IC-W32E

[. . . ] INSTRUCTION MANUAL DUAL BAND FM TRANSCEIVER iC-w32a iC-w32e This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. CAUTIONS RWARNING!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in) away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-W32A and IC-W32E. RWARNING! [. . . ] w Push [(H/L)(SET)J] or [(TONE)K] several times until "RT" appears as shown above. e Rotate [DIAL] to select the desired subaudible tone. · Each operating band for each display and each memory channel have independent settings. r Push [(VFO)CLR] to set the condition and to exit set mode. · Subaudible tone frequency list 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 q Push [VFO] to select VFO mode. e Push [(H/L)(SET)J] or [(TONE)K] several times until "OW" appears as shown above. r Rotate [DIAL] to select the desired offset (separately selectable for each band). · Pushing [(VFO)MHz] for 2 sec. selects MHz steps. (Unit: Hz) 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 t Push [(VFO)CLR] to set the condition and to exit set mode. 20 REPEATER OPERATION 5 s Auto repeater function (U. S. A. version automatically activates the repeater settings (duplex ON/OFF, duplex direction, tone encoder ON/OFF) when the operating frequency falls within or outside of the general repeater output frequency range. The offset and repeater tone frequencies are not changed by the auto repeater function, reset these frequencies, if necessary. · Frequency range and offset direction FREQUENCY RANGE 145. 200­145. 495 MHz 146. 610­146. 995 MHz 147. 000­147. 395 MHz 442. 000­444. 995 MHz USING DUPLEX DIRECTION "­DUP" appears "DUP" appears­ "DUP" appears­ "­DUP" appears Initial set mode 447. 000­449. 995 MHz SETTING THE AUTO REPEATER FUNCTION Activates for duplex only. Activates for duplex and tone. q Turn power ON while pushing [(H/L)SET] to enter initial set mode. w Push [(H/L)(SET)J] or [(TONE)K] several times until "AR" appears as shown above. e Rotate [DIAL] to turn the auto repeater function ON ("ON1" and "ON2") or OFF. 21 6 MEMORY/CALL PROGRAMMING s Programming during selection q Assign the main band to the desired display with [MAIN]. e Set the desired frequency: Set the frequency using the keypad or [DIAL]. offset frequency, duplex direction, subaudible tone frequency, etc. ), if required. r Push [S. MW] momentarily to indicate memory channels. · Do not hold [S. MW] for more than 0. 5 sec. , otherwise the memory channel will overwrite the displayed number. s General The transceiver has 100 memory channels (plus 5 pairs of scan edge channels) and 1 call channel on each band for storage of often-used frequencies. Avionics band frequencies are stored in the VHF memory channels (U. S. A. and Asia versions only). D Memory/call channel contents The following information can be programmed into memory/ call channels: · Operating frequency · 8-digit memory name*1 · Duplex direction (DUP or ­ DUP) with an offset frequency (pgs. *2 Except for the scan edge memory channels. t Rotate [DIAL] to select the desired channel. · Call channel (CAL) and scan edge channels (1A­5B), as well as regular memory channels, can be programmed in this way. y Push [(S. MW)MW] for 2 sec. to program. [EXAMPLE]: Memory programming of ch 40 during selection. Set frequency and other data. MAIN S. MW MAIN momentarily T SQL DUP 22 MEMORY/CALL PROGRAMMING 6 s Programming after selection q Assign the main band to the desired display with [MAIN]. Rotate [DIAL] or push 2 digit keys to select the memory channel (only programmed memories can be selected). e Set the desired frequency in VFO mode: Push [VFO] to select VFO mode. offset frequency, duplex direction, subaudible tone frequency, etc. ), if required. [. . . ] · Charge the battery pack or place new dry cell batteries in the battery case. · Set squelch to automatic (AT) or the squelch closed point (SQ1 or more). · Push [BAND] to select an amateur band, memory channel or avionics band. -- p. · Transmitting is impossible. · Squelch level is too deep. [. . . ]