User manual ICOM IC-T42A

[. . . ] NEVER short the terminals of the battery pack. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. WORD DO NOT push [PTT] when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below ­25°C or above +55°C. The basic operations, transmission and reception of the transceiver are guaranteed within the specified operating temperature range. However, the LCD display may not be operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i DO NOT modify the transceiver for any reason. [. . . ] 14) *10-key versions only TX CODE CHANNEL SELECT KEY Push to enter the ID code channel selection mode directly. 13) *10-key versions only TX CODE CHANNEL UP/DOWN KEYS Push to select a TX code channel directly. ID-MR SELECT KEYS Recalls detected ID codes. 2 · Push this key, then select the ID code using [CH Up]/[CH Down]. · Up to 5 ID's are memorized. 2 Push and hold for 1 sec. SCRAMBLER FUNCTION Push to toggle the voice scrambler function ON and OFF. to enter user set mode. · During user set mode, push this key to select an item, and change the value or condition using [CH Up]/[CH Down]. Push and hold this key for 1 sec. User set mode is also available via the `Power ON function. ' Refer to (p. OPT OUT KEYS Push to control the output signal level of the optional ports in the optional unit connector. Scanning stops when receiving a call. I Call procedure When your system employs tone signaling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signaling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 5-tone code according to your System Operator's instructions. · This may not be necessary depending on programming. Entering the user set mode: q While pushing and holding [Side2] and [Side3], rotate [VOL] to turn the power ON. Then push [CH Up] or [CH Down] to set the desired level/condition. · Available set mode functions are Backlight, Beep, Beep Level, SQL Level, Mic Gain, Battery Voltage and Signal Moni. r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. The digit to the right will blink automatically. · When the 10-keypad* is used for setting, the digit to be edited moves to the right automatically without pushing [TX Code Enter]. y Repeat r and t to input all allowable digits. u After setting the last digit, push [TX Code Enter] to set the code and return to the stand-by mode. *10-key versions only e Rotate [VOL] to turn the power OFF to exit user set mode. NOTE: User set mode is also available via a programmable function key. 9) D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. e Push [DTMF Autodial] to transmit the DTMF code in the selected DTMF channel. 14 BASIC OPERATION 3 I Emergency transmission When [Emergency Single] or [Emergency Repeat] is pushed, an emergency signal is automatically transmitted for the specified time period. When [Emergency] is pushed, the DTMF emergency signal is transmitted on the priority channel. When [Emergency Single] or [Emergency Repeat] is pushed for the specified time period, the DTMF emergency signal is transmitted once or repeatedly on the emergency channel. However, when no emergency channel is specified, the signal is transmitted on the previously selected channel. I Stun function When the specified ID, set as a killer ID, is received, the stun function is activated. [. . . ] And insert the transceiver into the belt clip until the base clip inserted fully into the groove. I MB-93 contents Qty. q Belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 w Base clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a `click' sound. r Once the transceiver is locked in place, it swivels as illustrated below. Once the transceiver is locked in place, it will swivel 360 degrees. 22 OPTIONAL SWIVEL BELT CLIP 6 I Detaching q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. [. . . ]