User manual ICOM IC-R20

[. . . ] INSTRUCTION MANUAL COMMUNICATIONS RECEIVER iR20 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-R20 COMMUNICATIONS RECEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] qSelect the desired bank contents to be transferred or erased from the bank. While pushing [BAND], rotate [R-DIAL] to select the desired memory bank group. to enter the select memory write condition. · 1 short and 1 long beeps sound. · Displays the original memory channel number automatically and µ "µ " indicator blinks. · Do not hold [MR S. MW] for more than 2 sec. , otherwise the memory contents will be copied to VFO. Push -DUP TSQL MODE FM ANL MR S. MW ePush [8 SET] once to select "BANK. " · While pushing [8 SET] then rotate [R-DIAL] also selectable "BANK. " rWhile pushing [BAND], rotate [R-DIAL] to select the desired bank group to be transfer. · Select "­ ­ ­ ­" indication when erasing the contents from the bank. When transferring FM When erasing FM >BANK-:R-00 -BNAME: -MNAME: -SKIP-:OFF >CLEAR 145. 700 µ . 028 µ . >BANK-:----BNAME: -MNAME: -SKIP-:OFF >CLEAR 145. 700 028 t Rotate [R-DIAL] to select the desired bank channel. y Push [MR S. MW] for 1 sec. for 1 sec. FM AFC B:GROUP1 145 700 µ A93 PSKIP ATT µ 642 . -BANK-:A-93 -BNAME:OSAKA -MNAME: -SKIP-:OFF >CLEAR 145. 700 33 SCAN OPERATION Scan types Scanning searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. 7 There are 7 scan types and 4 resume conditions to suit your operating needs. 35) 150 kHz Scan Jump 3304. 999 MHz Repeatedly scans all frequencies over the entire band. Some frequency ranges are not scanned according to the frequency coverage of the receiver's version. Used for checking for frequencies within a specified range such as repeater output frequencies, etc. SELECTED BAND SCAN Repeatedly scans all frequen(p. 35) Band edge Scan Jump Band edge cies over the entire selected band. 6 PROGRAMMED SCAN (p. 37) Band edge Scan edges xxA Scan Jump Band xxB edge MEMORY (SKIP) SCAN (p. 37) SKIP M1 M0 M 199 M6 M5 M2 M3 M4 SKIP Repeatedly scans memory channels except those set as skip channel. Skip channels can be turned ON and OFF by pushing and holding [5 SKIP] in memory mode. ALL/SELECTED BANK SCAN (p. 37) SKIP A00 A99 A98 A05 A04 A01 A02 A03 Repeatedly scans all bank channels or selected bank channels. The skip scan is also available. FREQUENCY/MEMORY SKIP FUNCTION (p. 39) Band edge Scan SKIP Jump SKIP Band edge SKIP Skips unwanted frequencies or channels that inconveniently stop scanning. This function can be turned ON and OFF by pushing and holding [5 SKIP] in either VFO or memory mode. 34 7 SCAN OPERATION Full/band/programmed scan q Select VFO mode with [VFO MHz]. · Select the desired frequency band with [BAND], if desired. r To start the scan, release [MODE SCAN]. · Scan pauses when a signal is received. [. . . ] (In this example, the USB serial port number is "3. ") iClose the Device Manager, System Properties screen and then Control panel. 91 q Cut w Fold e Complete POCKET GUIDE 18 Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc. iR20 VFO mode selection Push [VFO MHz] momentarily to select VFO mode. Memory mode selection Push [MR S. MW] momentarily to select memory mode. [. . . ]