User manual ICOM IC-F4

[. . . ] 1 2 PANEL DESCRIPTION IC-F3, IC-F4 IC-F3S, IC-F4S y y q q u u w w i e o r e i o r t 2 DEALER-PROGRAMMABLE FUNCTIONS q VOLUME CONTROL [OFF/VOL] Turns power ON and adjusts the audio level. (SmarTrunk mode only) r DEALER-PROGRAMABLE KEYS ­ [P0]/[P1]/[P2]/[P3]/[A]/[B]/[C]/[D]/ []/[ ]/[­] Can each be programmed for one of several functions by your Icom Dealer (see right). o FUNCTION DISPLAY Displays the following the information: · CH number. · Audible indication. 3 I General Consult your Icom Dealer or System operator for details concerning your transceiver's programming. [. . . ] · When a tone signalling system is used, the call procedure described at right may be necessary. w Push the call switch (assigned to one of the dealer programmable switches: [P0], [P1], [P2], [P3], [A], [B], [C], [D], [], [ ] and [ ­ ]). e After transmitting a 5-TONE code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling r Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your transmitted signal, pause a few secs. after pushing [PTT], hold the microphone 10 to 15 cm from your mouth and speak at a normal voice level. P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B C D P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B C D P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B C D P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B C D P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B 1 C 4 D 7 8 0 9 C D 5 6 B 2 3 A P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B C D P0 1 4 7 P1 2 5 8 0 P2 3 6 9 P3 A B C D P0 P1 P2 P3 7 4 CONVENTIONAL OPERATION I Tx code channel selection Your radio may be programmed for Tx code channel selection. In this case, you can choose a Tx code channel to be transmitted when using the call function (p. 7). · For a group call, you hear a short ring followed by two short beeps. D Receiving a landline-to-subscriber call *1 When you hear ringing, push [M] to answer. · For a group call, you hear a short ring followed by two short beeps. D Terminating a call *1 After completing a call, push [#] to disconnect (hang up). IMPORTANT: If one person in the conversation terminates a call, all participants will be cut off. D Last number redial *1 Push [M], [M] to automatically redial the last number called. · A high-pitched beep indicates that the number is accepted. *1: This function is available to for the IC-F3S/IC-F4S when the YZ [Y]/[Z] keys are assigned the [ M]/[#] key functions. 9 5 SmarTrunk IITM OPERATION D Memory speed-dialing *2 To automatically dial a commonly used number from memory: · Push [M] followed by the memory location (0­9). D Placing a telephone call *2 Enter the phone number followed by [1], [M]. · When the called party answers, push the [PTT] switch to talk, and release it to listen. D Calling another local system subscriber *2 Enter the subscriber number followed by [3], [M]. · You hear ringing, then two short beeps when the subscriber answers. · If the other subscriber is on another call or out of range, you hear a fast busy signal and the call terminates automatically. D Clear channel alerting *1 If all channels are busy, the transceiver automatically begins searching for an open channel and beeps every ten seconds. When two short beeps (low-pitched, then high-pitched) are heard, a channel is available. D Turbo SpeeDial To automatically dial a commonly used number with one push: · Push one of the turbo SpeeDials : IC-F3/IC-F4: [A], [B], [C] or [D] IC-F3S/IC-F4S: [P0], [P1], [P2], [P3], or [­] D Programming memory speed dial q Push and hold [M] until you hear a high-pitched beep. w Enter the memory location (0­9, A, B, C, D), the telephone or subscriber number, then [1], [M] (or [3], [M] if for another system subscriber). · Memories [A]­[D] are used for the Turbo SpeeDial. NOTE: This function is available for the IC-F3/IC-F4 only. *1: This function is available for the IC-F3S/IC-F4S when the YZ [Y]/[Z] keys are assigned the [ M]/[#] key functions. Use the Turbo SpeeDial function instead. D Emergency call *2 Push [0], [M] to initiate an emergency call. [. . . ] Battery pack BP-195 BP-196 Voltage/capacity 9. 6V/ 700mA 9. 6V/ 1050mA Charging period with BC-119 Approx. 2. 0 hours 16 SPECIFICATIONS AND OPTIONS I Specifications · GENERAL Frequency coverage : IC-F3/S 136­150 MHz 146­174 MHz : IC-F4/S 400­430 MHz 440­470 MHz 470­500 MHz 490­512 MHz 490­520 MHz : 16K0F3E (wide) 8K50F3E (narrow) : ­22°F to +140°F : ­25°C to +55°C (IC-F3/S) ­20°C to +55°C (IC-F4/S) : 58 (W)×138. 5 (H)×37(D) mm : 390 g 8 I Options · HM-54/HM-46/HM-75A SPEAKER-MICROPHONES Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt clip. · BC-119 DESKTOP CHARGER (or BC-121 MULTI-CHARGER) + AD-81 DESKTOP CHARGER ADAPTER Used for rapid charging of battery packs. · BC-110A/D/V WALL CHARGER Used for charging via a domestic AC wall socket. [. . . ]